PVC TrimWelder™ Slow Cure

1 of 9 products in this brand

PVC TrimWelder™ Slow Cure is a medium-viscosity, solvent-free structural adhesive system that provides flexibility, toughness, and surface adhesion for bonding all forms of PVC to themselves, metals, or wood. Cured performance shows excellent adhesion and bond strength to nylons, polystyrene, fiberglass, reinforced plastics, stone, ceramics, and most plain and plated metal components. This material can withstand thermal cycling and shock loading between dissimilar materials. Slow Cure is ready to handle in 90 - 120 minutes.

Product Type2K (2 component) Adhesive, Structural Adhesive

Application AreaComposite Industrial Panel, Panels

Compatible Substrates & SurfacesCeramic, Composites, Fiberglass, Metal, Nylon, Polyvinyl Chloride (PVC), Stone, Wood

Chemical FamilyAcrylics & Acrylates, Acrylics, Acrylates & Methacrylates

FeaturesExcellent Flexibility, Excellent Toughness, Fast Curing, Good Adhesion, Good UV Resistance, High Impact Resistance, Long Open Time, Medium Viscosity, Paintable, Peel Resistance, Shock Resistant, Thermal Cycle Resistance, UV Resistant

Technical Data Sheet

Enhanced TDS

Identification & Functionality

Product Information
Technology / Base Two-component Methylmethacrylate (MMA)
Type of Product MMA
Curing Mechanism Polymerization
Appearance / Color White
Consistency Liquid

Features & Benefits

Key Attributes
  • Excellent adhesion to plastics and metals
  • Great impact resistance and peel strength
  • Matches white PVC trim boards
  • Paintable, sandable and UV resistant
  • Longer open time for larger applications
  • Easy to apply and solvent free
  • Fills nail holes and gaps up to 3/8"
  • Meets 2009 EPA VOC & CARB requirements
Product Highlights
  • PVC TrimWelder™ Slow Cure adhesive does not require special surface preparation and does not contain any solvents.
  • It will work successfully in most applications without preparation. Our slow cure system is so strong that it appears to weld the PVC together.
  • This adhesive has a creamy consistency that will not foam, run or drip.
  • PVC TrimWelder™ Slow Cure is fast-curing, two-component product with an open time of 20 - 25 minutes at 73°F after thorough mixing with approved mix tips.
  • It will cure satisfactorily at application temperatures as low as 40°F.

Applications & Uses

Cure Method
Application Instructions
  • Combine resin and activator in equal volume and mix thoroughly. For convenience and accuracy use pre-measured cartridges with disposable static mixers. Open time is 20 - 25 minutes at room temperature. Handling strength within approximately 90 - 120 minutes.
  • Consult the packaging instructions on proper preparation, application and clean up.

Properties

Color
Physical Form
Cured Properties
ValueUnitsTest Method / Conditions
Impact Resistance (on steel)20ft.lbs/in²
Lap Shear Strength (Grit blasted steel)3365psi
Hardness75.0Shore D
Adhesive Testing (on plastics, PVC, ABS glass filled nylon, stirene)Substrate failure
Thermal Service Range-65 - 260°F
Chemical ResistanceExcellent
Elongation60.0%
Peel Strength (on Aluminum)20 - 25psi
Lap Shear Strength (Aluminum)3390.0psi
Typical Film Thickness0.03inches
Uncured Properties
ValueUnitsTest Method / Conditions
Viscosity (Mixed, at 25°C)50000cPs
Flash Point51.0°FCleveland open cup
ToxicityModerate
SolventsNone
Mix Ratio1 : 1
Specific Gravity (at 20/20°C)1.01
FillersYes
Clean Up SolventsMEK, Acetone

Safety & Health

Safety Precautions

To minimize the risk of skin contact, we recommend the use of eye protection, gloves and protective clothing when working with this material. Prevent the build-up of vapors. Extinguish all sources of ignition during use.

Packaging & Availability

Country Availability
Packaging Type
Regional Availability
  • Africa
  • Asia Pacific (Excluding Russia)
  • Europe (Excluding Russia)
  • India
  • Latin America
  • Middle East
  • North America
  • USA
Packaging Information

Side-by-side cartridges

Storage & Handling

Shelf Life
12 Months
Storage Information

Store in an unopened original container in a cool, dark area between 55°F to 75°F.