Enhanced TDS
Identification & Functionality
- Chemical Family
- Technologies
Features & Benefits
- Ready-to-Use Product Features
- Features and Benefits
- Excellent bond strength to a wide variety of substrates
- Low Exotherm
- Good thermal performance
- Good chemical resistance
- Non Sag
- High Flexibility
Applications & Uses
- Markets
- Applications
- Compatible Substrates & Surfaces
- General Instructions
Surfaces to be bonded must be clean, dry and free from grease, oil, wax, weak oxide films and other contaminants. Bring both components to room temperature prior to mixing. Measure out specified amounts of parts A and B and mix, without introducing bubbles, until homogenous. Meter-mix equipment equipped with an automatic purge is recommended for higher volume applications. Contact your H.B. Fuller representative for suggested application equipment to suit your specific needs. We recommend that containers be purged with nitrogen after they are opened to the air and not all the material is used.
Properties
- Color
- Physical Form
- Component A
- Component B
- Cured Mechanical Properties
- Technical Data
- Uncured Properties
- Rheological Properties
| Value | Units | Test Method / Conditions | |
| Viscosity | 16000.0 | cP | - |
| Value | Units | Test Method / Conditions | |
| Viscosity | 83000.0 | cP | - |
| Value | Units | Test Method / Conditions | |
| Overlap Shear Strength (E-Coat steel, IPA wipe, at 50% RH) | 24.9 | MPa | ASTM D1002 |
| Overlap Shear Strength (Polycarbonate, IPA wipe, at 50% RH) | 13.8 | MPa | ASTM D1002 |
| Overlap Shear Strength (GFPC, abraded, at 50% RH) | 14.3 | MPa | ASTM D1002 |
| Overlap Shear Strength (Nylon 6-6, abraded, at 50% RH) | 7.2 | MPa | ASTM D1002 |
| Overlap Shear Strength (ABS, IPA wipe, at 50% RH) | 4.4 | MPa | ASTM D1002 |
| Overlap Shear Strength (Electrogalvanized steel, IPA wipe, at 50% RH) | 13.1 | MPa | ASTM D1002 |
| Overlap Shear Strength (Aluminum, abraded, at 50% RH) | 15.2 | MPa | ASTM D1002 |
| Overlap Shear Strength (Stainless steel, abraded, at 50% RH) | 22.3 | MPa | ASTM D1002 |
| Overlap Shear Strength (Cold rolled steel, abraded, at 50% RH) | 20.7 | MPa | ASTM D1002 |
| Value | Units | Test Method / Conditions | |
| Hardness | 65.0 | - | - |
| Open Time | 4.0 | min | - |
| Value | Units | Test Method / Conditions | |
| Tack Free Time | 15.0 | min | - |
| Specific Gravity | 1.31 | - | - |
| Gel Time (at 23°C, 100 gram) | 3 - 5 | min | - |
| Weight Mix Ratio | 1900-01-03T06:05:00+00:00 | - | - |
| Full Cure (2 hours, at 80°C) | 18.0 | h | - |
| Value | Units | Test Method / Conditions | |
| Viscosity (Mixed) | Thixotropic paste | - | - |
Packaging & Availability
- Regional Availability
Storage & Handling
- Shelf Life
- 6 Months
- Storage Conditions
These materials should be stored in a dry environment within a temperature range of 16 °C to 27 °C (60 °F to 80 °F). Extremes of temperature beyond this range may result in crystallization or polymerization of the materials. Introduction of a nitrogen blanket into the containers before closing will improve the storage life of the products. A wide variety of cleaning solutions are available for cured and uncured epoxies and polyurethanes. For more information on proper recommendations and procedures, contact the Technical Department.