Hydra FAST-EN® DC-13431

1 of 18 products in this brand
Hydra FAST-EN® DC-13431 is a water-based adhesive designed for use in foam fabrication that can be sprayed or coated. Its primary purpose is to bond open-cell polyurethane foam to itself, and it can be used in a 2-part spray operation or as a wet laminating 1-part spray or coating adhesive.

Chemical Family: Polychloroprenes, Zinc & Zinc Compounds

Product Type: 2K (2 component) Adhesive, Solvent free (100% Solids) Adhesive, Waterborne Adhesive

Application Area: Foam Fabrication

Application Method: Spray

Compatible Substrates & Surfaces: Foam

Features: Color Tinted, Easy To Clean, Equipment-friendly, Flame Retardant, High Solids Content, Long Shelf Life, Low Toxicity, Quick Bonding, Wide Temperature Operating Range

Technical Data Sheet
Message our experts with questions
Robert Blackstone avatar

Robert Blackstone

Global Leader - Inside Sales

Please reach out to me with any questions, I am happy to assist you in finding the right product or learning more about our storefront

Enhanced TDS

Identification & Functionality

Features & Benefits

Labeling Claims
Ready-to-Use Product Features
Product Features
  • Water-based - No VOC's, low toxicity, easy clean-up.
  • High solids - 51%
  • Quick Bonding - Immediate for 2-part process; Quick converting in 1-part applications
  • High F/R level - Bondlines provide substan-tial flame retardancy to assembled parts.
  • Soft Seams - Bondlines remain soft and resist dimpling.
  • Color tint available - Aids in noting coverage and uniformity: Standard color is white.
  • Environmentally Friendly - Neither wet nor dry adhesive is considered a RCRA hazardous waste
  • Equipment friendly - Can be sprayed or coated
  • Temperature range - The applied adhesive when dry has a use range of -40 to 180°F (under normal conditions).

Applications & Uses

Markets
Applications
Application Area
Application Method
Compatible Substrates & Surfaces
Application
  • The adhesive can be used in a 2-part spray operation or as a wet laminating 1-part spray or coating adhesive. The 2-part operation requires DC-12239 part B and gives good immediate bond strength and does not require oven drying.
  • DC-13431 when used in a wet laminating process does require sufficient drying to convert adhesive from the liquid to the solid phase. The bonding surfaces should be held in contact during the drying operation. Drying conditions vary according to wet laydown, porosity of materials being bonded, and process drying conditions.
  • DC-13431 can provide substantial bondline flame retardancy to the materials bonded. Laydown required is dependent upon the flame retardancy of the materials bonded and final product F/R requirements. This must be determined by the end user. Higher laydowns will provide increased F/R performance.
Bonding Capabilities
  • Hydra FAST-ENTM DC-13431 can be color tinted to aid the operator in the correct amount to be applied. Custom colors are available at no extra charge. The color tint also aids the operator in determining if uniform coverage is being achieved. For urethane foam recommended laydown is around 10 grams wet /ft². Actual laydown should be adjusted to reflect desired adhesion and flame retardancy levels.
  • DC-13431 when used in a 2-part scenario requires the use of DC-12239 as an activator (Part B). A 2-part spray gun is required. Part B flow rate should be adjusted to guarantee full conversion of Part A to a solid adhesive film. The following are recommended approximate mix ratios:

 

By Volume or Weight

DC-13431 Part A 100
DC-12239 Part B 10 - 20
  • These parameters are adjusted by air pressure settings to achieve the effect desired. The air supply used must be consistent (no wide fluctuation in line pressures) and be oil free to achieve the best results.
  • Atomizing air pressures can be adjusted over a wide range to meet specific requirements. Sprayed parts in a 2-part scenario can be mated immediately. Ample mating pressure should be applied to assure uniform contact. Mated parts can be handled immediately.
Application and Cleaning Information

Easy Clean-up:

  • Clean up is easily accomplished using a commercially available liquid detergent (Pinesol) in a 5 -10% water solution. Tap water alone is not recommended for clean up.

Precautionary Data:

  • This product is nonflammable when wet
  • For professional or industrial use only
  • Use with adequate ventilation
  • Keep away from children
  • Keep container closed when not in use
  • Protect from freezing

Properties

Color (Properties)
Soluble in
Water (Component A), Water (Component B)
Component A
ValueUnitsTest Method / Conditions
Solid Content51.2%-
Viscosity (at 10 rpm, spindle 2)1500.0cPActivator Brookfield Dv-II #7
Weight per Gallon9.89lb-
Specific Gravity1.19--
pH11.5--
Component B
ValueUnitsTest Method / Conditions
Solid Content15.0%-
ViscosityWater thin--
Weight per Gallon9.3lb-
Specific Gravity1.115--
pH3.5--

Storage & Handling

Shelf Life
1 Year (Part B), 12 Weeks (Part A)