Enhanced TDS
Identification & Functionality
- Product Type
- Technologies
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Product Highlights
- Patch 1⁄2" (12 mm) down to a featheredge
- Fast setting-install flooring in 30 to 45 minutes
- Latex modified smooth surface patch
- Use on wood, concrete and most other existing flooring materials
- Self-drying formula
- Contributes to LEED® project points
- VOC 0
Applications & Uses
- Markets
- Applications
- Application Area
- Coverage
Coverages shown are approximate. Actual coverages may vary according to substrate conditions and thickness of applications.
Application Depth
Approximate Coverage per 25 Ibs. (11.34 kg) per 9.75 Ibs. (4.42 kg) ⅛" 26-29 sq.ft. 10-11.5 sq.ft. ¼" 13-14 sq.ft. 5-5.5 sq.ft. ½" 6-7 sq.ft. 2.5-2.75 sq.ft. - Suitable Substrates
- Concrete
- Cement backerboards
- Concrete terrazzo
- Ceramic tile, pavers, brick
- Quarry tile
- Exterior grade plywood, C-C (plugged) or better
- Exterior Grade Lauan Plywood—Type I Trademarked Exterior Grade, OVL, CC, BB, OVL face grades only (Note: Lauan plywood is an unacceptable substrate for the installation of resilient, ceramic or marble tile)
- Vinyl composition tile (VCT), embossed resilient floor coverings must be single layer and well bonded to an approved substrate.
- Adhesive residue (except for tacky or pressure sensitive adhesive)
- Gypsum substrates—minimum tensile bond strength 72 psi (0.5 MPa)
- Substrate Preparation
- All surfaces must be structurally sound, dry and free from oil, grease, dust, loose or peeling paint, sealers, floor finishes, curing compounds or any contaminant that would prevent a good bond.
- Concrete and cementitious substrates must be fully cured and free of any hydrostatic pressure or excessive moisture [15 lb. per 1000 ft2 (0.07 kg/m2 ) per 24 hours, RH 99% or lower].
- TEC® VersaPatch® can be installed over green concrete with RH of 99% or less. This product is not a moisture vapor barrier.
- If substrate moisture content exceeds the maximum allowed by the flooring manufacturer, then moisture mitigation must be applied prior to application of VersaPatch®.
- To reduce moisture vapor emissions to an acceptable level, use TEC® LiquiDamTM Penetrating Moisture Vapor Barrier or LiquiDam EZTM Moisture Vapor Barrier.
- All surface protrusions must be removed by sanding, scraping or chipping. Remove all dust by vacuuming. Not recommended for use over expansion or control joints.
- Limitations Information
- Only for interior use.
- Do not use where there is hydrostatic pressure or excessive moisture conditions.
- Not for use as a wear surface or to patch over sealed concrete, epoxy terrazzo, tempered hardboard, particle board, strip wood flooring, over heavily cushioned flooring or perimeter bonded flooring.
- Do not apply when the temperature is below 50°F (10°C).
- Application Instruction
For best results, VersaPatch® Latex Modified Floor Patch and room should be at 50°F to 70°F (10°-21°C) for 24 hours before, during and 48 hours after installation. In a clean mixing container, add product to clean, cool, water as specified in the chart.
Size Water 25 lbs. (11.34 kg) 3 to 4 quarts (2.8 to 3.8 L)
9.75 lbs. (4.42 kg) 43 ⁄4 to 61 ⁄3 cups (1.12 to 1.5 L)
- Add powder to liquid for ease of mixing. Mix thoroughly to a smooth, lump-free consistency.
- For smaller amounts use a ratio of 3 parts powder to 1 part water.
- Avoid breathing dust and contact with eyes and skin.
- Avoid using high speed mixing - not to exceed 300 rpm.
- Mix only as much patching compound as can be used in 10 to 15 minutes. Use immediately.
- Recommended Applications
- Immediately after mixing, work the VersaPatch® into the void to be filled with a flat steel trowel and then finish to a level surface to the required smoothness. The working time for this product is 10 to 15 minutes depending upon the temperature.
- High temperature will shorten the working time. For repairs greater than 1⁄2" (12 mm) in thickness, you will need two applications, allowing the first application to set before applying the second. Do not exceed a total thickness of 1" (25 mm) of VersaPatch®. Do not overwork the product.
- Curing
VersaPatch® is fast drying and can accept foot traffic and the installation of most floor covering materials within 30-45 minutes. Protect from excessive heat or drafty conditions during curing period.
- Cleaning Instructions
Wash tools, hands and equipment with warm soapy water while material is still fresh.
Properties
- Color
- Physical Form
- Appearance
- Dry gray powder
- Physical Properties
| Value | Units | Test Method / Conditions | |
| Install Floor Covering | 30 - 45 | Minutes | — |
| Pot Life | 10 - 15 | Minutes | — |
Regulatory & Compliance
- Certifications & Compliance
- Chemical Inventories
Packaging & Availability
- Packaging Type
- Packaging Information
- 25 lb. plastic bags (11.34 kg)
- 25 lb. moisture-resistant bags (11.34 kg)
- 9.75 lb. Pure Pak container (4.42 kg)
Storage & Handling
- Storage and Handling Conditions
- Store in a cool, dry area away from direct sunlight. Do not store open containers.
- Maximum shelf life is from date of manufacture in unopened package.
- Plastic bag: 3 years
- Moisture-resistant bag: 1 year
- Pure Pak: 1 year