Swift®col 2607-03 A is a solvent-based 2-component adhesive formulated with polyurethane. It is designed for a variety of bonding applications, including stress and flat surface bonding, as well as edge bonding. This adhesive is suitable for adhering materials such as foils, carpets, textiles, foams, genuine and artificial leather, etc., to fibrous materials, GRP, wood-based composites, SMC, and more. It is commonly used in the manufacture of bodywork moldings, including headlinings, door and side panels, pillar coverings, rear shelves, and similar components.

Product Type: 2K (2 component) Adhesive, Solventborne Adhesive

Application Area: Automotive Interior Trim

Compatible Substrates & Surfaces: Carpet, Foam, Foils, Glass-reinforced Plastic (GRP), Leather, Sheet Molding Compound (SMC), Textiles, Wood

Application Method: Brush, Spray

Chemical Family: Polyurethanes (PU)

Technical Data Sheet
Message our experts with questions
Robert Blackstone avatar

Robert Blackstone

Global Leader - Inside Sales

Please reach out to me with any questions, I am happy to assist you in finding the right product or learning more about our storefront

Enhanced TDS

Identification & Functionality

Features & Benefits

Product Highlights
  • Application by spraying
  • Low activating temperature
  • Process security
  • Fully meets the high standards of the automotive industry
  • Slightly yellowing under uv radiation

Applications & Uses

Markets
Applications
Application Area
Application Method
Compatible Substrates & Surfaces
Recommended Applications

This product is suitable for stress as well as for flat surface bonding and edge bonding of foils, carpets, textiles, foams, genuine and artificial leather etc. to fibrous materials, GRP, wood based composites, SMC, etc. for bodywork moldings, e.g. headlining, door and side panels, pillar covering, rear shelfs, etc.

Suitable Substrates

Foils, carpets, textiles, foams, genuine and artificial leather, fibrous materials, GRP, wood based composites, SMC, etc.

Application Information

Laminating technique:

  • Vacuum deep drawing, stamp covering and manual lamination.
  • The product can be applied by spray gun or by brushing.

Surface preparation:

  • Surfaces should be clean and free from dust, fatty substances and release agent.
  • If necessary plastic carriers have to be pre-treated with primers, sanding, sandblasting, etc.

Attention: 

  • The surface tension of the substrates to be bonded must be higher than 38 mN/m.

Mixing ratio: -

  • 100 parts by weight of Component A with 6 parts by weight of Component B 9151 or 9619 - 100 parts by weight of Component A with 3 parts by weight of Component B 2541 - Shake hardener well before adding to the adhesive.
  • Component B should be added during mixing homogeneously and without foaming into Component A using a mechanical mixing equipment.

Working temperature: between 15°C and 25°C. - The product could be applied out of a pressure feeding container using a spray gun or by brushing.

Processing time/pot life: between 15°C and 25°C. To be processed at 20°C material temperature within 8 hours upon adding the hardener.

Attention: higher temperatures decrease the processing time, i.e. 4 hours at 30°C.

Drying conditions:

  • At room temperature or in a ventilated oven at a maximum temperature of 50°C.
  • The drying time depends on the absorbency of the substrate, the coating weight, the humidity and the ambient temperature.

Bonding:

  • To achieve the best bonding you must consider the cycle time, the temperature of the carrier and of the laminate, the activation temperature and the lamination pressure.
  • This 2-component adhesive attains its final adhesive properties, e.g. heat resistance, after 3 days (72 hours) after bonding.

Properties

Typical Properties
ValueUnitsTest Method / Conditions
Working Temperature15 - 25°C-
Pot Life (at 15°C - 25°C)8.0Hours-

Storage & Handling

Shelf Life
6 months
Storage Conditions
  • In original sealed packaging protected from sun, dust, moisture and high temperatures.
  • Clean and dry conditions above 10°C and below 30°C. Keep away from freezing.