Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
- Product Image
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Key Attributes
Features Benefits Single component No mixing, consistent material quality
Isocyanate free Enhanced safety
Elastomeric Remains flexible, absorbs stresses
No solvents No flame hazards
Applications & Uses
- Applications
- Application Area
- Application Method
- Compatible Substrates & Surfaces
- Cure Method
- Basic Use
Millennium LPS is a multi-use sealer that can be used for:
- Adhering Millennium Lockin’ Pocket® to approved substrates
- Sealing around penetrations prior to Lockin’ Pocket® Installation
- Repairing splits, cracks, holes and other membrane defects
- Mid-level construction grade adhesive and sealant
- Lightning protection attachment
- Shingle repairs
- All purpose sealer
- Approved Insulations and Substrates
- Granule surfaced Modified Bitumen
- EPDM
- TPO
- Metal
- Smooth surfaced asphalt Built-Up Roofs (BURs)
- Gravel surfaced BUR
- Asphalt coal tar pitch (BUR)
- Concrete
- Wood
- Aluminum
- Stone
- Limitations
- Do not apply to a wet surface.
- Requires atmospheric air and moisture to properly cure.
- Equipment
Professional 10 oz. (300ml) manual, pneumatic, or battery powered caulk gun.
- Surface Preparation
The substrates must be clean, even, dry, free of dust, oil, grease and any contaminants that could inhibit bonding. All traces of poorly adhered paints or coatings should be removed prior to the application of LPS. For applications on granule surfaced modified bitumen membranes, remove all loose granules from the surface of the membrane prior to installlling Millennium LPS.
If the substrates need to be cleaned, solvents such as methylethylketone (MEK) or acetone may be used. Check the compatibility of the solvent used with the substrates. Allow the substrate to dry after cleaning. Caution: When using solvents, extinguish all sources of ignition and carefully follow the safety and handling instructions given by the manufacturer or supplier.
For applications over existing weathered asphalt or coal tar pitch BUR, apply Millennium Universal Primer prior to the application of Millennium LPS. For applications over fresh and or non-oxidized asphalt, coal tar or plastic film membranes, apply Millennium Surface Treatment prior to the application of Millennium LPS.
- Application Method
1. Cut nozzle to desired size and puncture seal inside the nozzle.
2. Refer to Millennium Lockin’ Pocket® Inter-Locking Flashing System product data sheet for complete application instructions.
3. Gun/pump Millennium LPS around base of penetration to prevent Millennium Hurricane Force® Universal Sealer from flowing through the openings.
4. Apply a liberal bead of LPS to the substrate where Lockin’ Pocket® will be placed.
5. Apply a liberal bead of LPS to the locking joint of the Lockin’ Pocket®.
6. Set Lockin’ Pocket® onto bead of LPS and apply equal pressure to assure positive contact with the substrate.
7. Strike away excess LPS from base of placed Lockin’ Pocket®.
Properties
- Color
Packaging & Availability
- Packaging Type
- Regional Availability
- Packaging and Coverage
Millennium LPS is available in the following package:
Cartridge Size Case Part # Cartridges/Case 10.1 fl. oz. (300ml) LP-S10.1-12 12 Each cartridge will produce approximately 20 - 25 lineal feet (6 - 8 meters) of 1/2” (1.3cm) wide bead. Coverage rates will be determined by use and may vary when used over irregular surfaces.
Storage & Handling
- Shelf Life
- 12 Months
- Storage Conditions
Storage in high temperature and high relative humidity environments may reduce the shelf life of Millennium LPS. Shelf life is 12 months in unopened original packaging when stored at or below 80°F (27°C).