Millennium Hurricane Force® 1-Part Flashing Adhesive

1 of 55 products in this brand
Millennium Hurricane Force® 1-Part Flashing Adhesive is a highly elastomeric, one-part asphalt-modified urethane adhesive that is solvent-free and does not require mixing. The VOC content of the adhesive is less than 250 g/L. Millennium Hurricane Force® 1-Part Flashing Adhesive is approved for use in VOC regulated markets such as California and the OTC States.

Chemical Family: Urethanes

Product Type: 1K (1 component) Adhesive, Elastomeric Adhesive, Reactive Adhesive, Solvent free (100% Solids) Adhesive

Application Area: Roofing Substrates

Application Method: Trowel

Compatible Substrates & Surfaces: Concrete, Fiberglass, Gypsum, Masonry, Metal, Wood

Features: Flexible

Technical Data Sheet
Message our experts with questions
Robert Blackstone avatar

Robert Blackstone

Global Leader - Inside Sales

Please reach out to me with any questions, I am happy to assist you in finding the right product or learning more about our storefront

Enhanced TDS

Identification & Functionality

Chemical Family
Product Image

Features & Benefits

Ready-to-Use Product Features
Key Attributes
Features Benefits
Single component

Requires no mixing

Solvent free No odors
Elastomeric

Remains flexible, absorbs stresses

VOC content less than 250 g/L

Suitable for use in VOC regulated markets

Cold applied

Won’t burn, no exposure to oxidized asphalt fumes

Applications & Uses

Application Area
Application Method
Compatible Substrates & Surfaces
Basic Use

Millennium Hurricane Force® 1-Part Flashing Adhesive is specially formulated for use as a vertical grade flashing adhesive for bonding approved base sheets, vapor retarders and membranes for low slope roof applications. Millennium Hurricane Force® 1-Part Flashing Adhesive can also be used to seal head laps in modified bitumen roof membranes.

Millennium Hurricane Force® 1-Part Flashing Adhesive forms a strong bond to most substrates and does not soften or damage the membrane.

Approved Substrates
  • Concrete
  • Cinder and masonry block
  • Base sheets (sanded or
  • granule surfaced)
  • Plywood
  • Metal
  • Fiberglass insulation
  • Polyisocyanurate insulation
  • Perlite insulation
  • Wood fiber insulation
  • Polystirene (XPS, EPS)
  • Gypsum Cover board
  • High density polyisocyanurate cover board

Approved Membranes

  • SBS modified bitumen base sheets
  • SBS modified bitumen mineral surfaced cap sheets
Limitations
  • Do not apply to wet or damp surfaces. This includes primers.
  • Allow solvent based primers to completely dry before using the adhesive.
  • Do not apply when surface temperatures are below 40°F (4°C).
Application Method

1. Ensure that the substrate is suitable for bonding and is clean, dry, and free of defects.

2. Apply Hurricane Force® 1-Part Flashing Adhesive with a 1/4” (0.6 cm) notched trowel directly to the backside of the flashing membrane (as shown) or to the bonding substrate.

3. Embed the flashing membrane into the freshly applied adhesive. Do not allow the adhesive to skin over. Apply pressure across the entire membrane surface to ensure full contact with the adhesive removing all wrinkles and air pockets.

4. A continuous bleed-out of adhesive should be present along all membrane side laps and tie-ins.

5. For multi-layer flashing applications repeat steps 2-4.

Surface Preparation

All work surfaces should be clean, dry, and free of dirt, dust, debris, oils, un-adhered coatings, deteriorated membrane or other contaminants that may result in a surface that is not sound or is uneven.

Properties

Color

Packaging & Availability

Packaging Type
Regional Availability
  • Australia & New Zealand (ANZ)
  • Latin America
  • North America
  • South East Asia
Packaging and Coverage

Millennium Hurricane Force® 1-Part Flashing Adhesive is available in the following package:

Pails Size Part # Pails/Case
5 Gallon (18.9L) HF-FA5P-01 36

 

Coverage rate is approximately 12-15 sq. ft. (1.1-1.4 m2) per gallon when applied with a 1/4” notched trowel which results in an approximately 1/8” (0.3 cm) thick layer of adhesive.
Coverage rates may vary when used over irregular surfaces.

Storage & Handling

Shelf Life
9 Months
Storage Conditions

Store material in original unopened packaging at temperatures between 40°F-100°F (4°C-38°C). For best results store material at temperatures between 60°F-80°F (15°C-27°C) just prior to use. Shelf life is 9 months when stored as recommended.