Enhanced TDS
Identification & Functionality
- Chemical Family
- Technologies
Features & Benefits
Applications & Uses
- Applications
- Application Area
- Application Method
- Compatible Substrates & Surfaces
- Cure Method
- Application Information
Applications
Fields of Application
Automotive Construction Industrial assembly
Transportation Processing
Suitable Substrates
Various galvanized steels
Various aluminum alloys
Various steel alloys
Duroplastics Thermoplastics (except PE, PP, PTFE)
Various composite materials (e.g. CFRP, GFRP)
Glass Mineralic materials
Wood Coated surfaces Consistency Non-sagging Pasty
Surface Requirements
Clean Free of grease Free of dust Surface Cleaning
Körasolv GL Körasolv PU Körasolv WL Adhesion Promoter (absorbing surface) Körabond HG 74 E
Application Method
Cartridge dispenser
Sachet dispenser
Dispensing system
Wet-in-wet (depending on paint)
Product Overpaintability Solvents Cleaning
Cleaner for Tools
Körasolv GL Körasolv PU Hints
Resistance against UV Radiation Not suitable for glass bonding with
permanent UV radiation to the bonding area.
Please ask your local sales office for
products suitable for such applicationsStress Cracking Preliminary tests must be carried out on
plastics with a tendency to stress cracking.
(PMMA, ABS, PC or PS)Compatibility with Polystyrene Foams Not suitable for bonding polystyrene foams.
Please ask your local sales office for
products suitable for such applications.- Preparation
For some substrates the use of mechanical pretreatment and/or cleaner or primer is necessary to achieve good adhesion.
- Processing
Low temperatures can cause a temporary increase in viscosity resulting in reduced extrusion and slower curing rates.
- Cleaning Instructions
Clean tools immediately after use. Once cured, the material can only be removed mechanically. Appropriate cleaners are listed in the product properties.
- Dimensioning
The required thickness of the adhesive layer depends on the expected maximum strength and joint movement. We recommend a minimum layer thickness of 2 mm.
Properties
- Physical Form
- Physical Properties
- Cured Properties
- Processing Parameters
- Recommended Operating Conditions
| Value | Units | Test Method / Conditions | |
| Density | 1.6 | g/cm³ | — |
| Solid Content | 100.0 | wt % | — |
| Glass Transition Temperature | -59.0 | °C | DIN EN ISO 6721-1 |
| Value | Units | Test Method / Conditions | |
| Skin Formation Time | 10.0 | min | Kö-test method 100109, Climate according to DIN 50014 |
| Curing to Depth (within first 24 h) | 3.0 | mm/d | Climate according to DIN 50014 |
| Hardness (after 28d, thickness of specimen = 6 mm) | 58.0 | — | DIN ISO 7619-1, Shore A |
| Tensile Strength | 2.3 | MPa | DIN EN ISO 527 |
| Elongation at Break | 300.0 | % | DIN EN ISO 527 |
| G10-Modulus | 1.3 | MPa | DIN EN 1465 |
| Lap Shear Strength (substrates: aluminum/aluminum) | 3.5 | MPa | DIN EN 1465 |
| Value | Units | Test Method / Conditions | |
| Processing Temperature | 5 - 35 | °C | — |
| Required Squeezing Pressure | 2 - 5 | bar | — |
| Recommended Minimum Layer Thickness | 2.0 | mm | — |
| Value | Units | Test Method / Conditions | |
| Service Temperature | - 40 - 80 | °C | — |
| Short-Term Temperature Resistance (30 min) | 120.0 | °C | — |
Packaging & Availability
- Country Availability
- Regional Availability
Storage & Handling
- Storage Conditions
Körapop 250 should be used within the shelf life specified on the packaging. The storage stability only applies to material stored in original unopened containers, at storage temperature 5°C to 25°C.