Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
- Product Image
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Key Attributes
Features Benefits Ready-to-Use Requires no pre-mixing, reduces labor costs
No temperature restrictions Suitable for all climates
One Step™ technology Easy to apply Solvent free Essentially VOC free, no odors
Elastomeric Remains flexible, absorbs stresses
High build formulation Suitable for vertical applications
Excellent bond Substitute for hot asphalt or solvent based adhesives
Fast setting Completely set within minutes of application
Applications & Uses
- Markets
- Application Area
- Basic Use
Millennium Hurricane Force® Lap and Flashing Adhesive is designed for bonding flashing as well as side laps and head laps in approved membranes. Millennium Hurricane Force® Lap and Flashing Adhesive is ideal for applications where hot asphalt or solvent based cold process adhesives cannot be used.
- Approved Substrates
- Concrete
- Cinder and masonry block
- Base sheets (sanded or
- granule surfaced)
- Plywood
- Metal
- Fiberglass insulation
- Polyisocyanurate insulation
- Perlite insulation
- Wood fiber insulation
- Polystirene (XPS, EPS)
- Gypsum Cover board
- High density polyisocyanurate cover board
Approved Membranes
- SBS modified bitumen base sheets
- SBS modified bitumen mineral surfaced cap sheets
- Limitations
- Do not apply to wet or damp surfaces.
- Not intended for insulation attachment.
- Not to be used with torch down membranes or membranes with plastic films.
- Surface Preparation
All work surfaces should be clean, dry, and free of dirt, dust, debris, oils, unadhered coatings, deteriorated membrane or other contaminants that may result in a surface that is not sound or is uneven.
- Equipment
The fast and dependable One Step™ applicators make applying Millennium Hurricane Force® Lap and Flashing Adhesive simple:
• Millennium One Step™ Battery Powered Applicator
• Millennium One Step™ Pneumatic Applicator- Application Method
1. With a utility knife, remove the molded tips at the groove from the One Step™ mixing head.
2. Attach a One Step™ mixing nozzle to the threaded mixing head.
3. Place the cartridge into the appropriate One Step™ applicator.
4. Dispense an initial amount of Millennium Hurricane Force® Lap and Flashing Adhesive into a waste container to ensure a proper mix, then diskard.
5. For lap adhesive Installation apply Millennium Hurricane Force® Lap and Flashing Adhesive in one continuous 3/4” - 1” (1.9 cm - 2.5 cm) wide bead down the center of the membrane’s selvage edge. As adhesive is applied immediately set membrane into wet adhesive.
6. For flashing installation apply the adhesive to the back side of the membrane or directly to the substrate in a ribbon pattern. Spread adhesive with a 1/4” (0.6 cm) notched or serrated trowel for full coverage applications. Immediately set flashing membrane in place.
7. For laps immediately roll with weighted roller to ensure positive contact between adhesive and membrane. For flashing immediately roll with a suitable hand roller.
8. Unused adhesive can be applied at a later date by simply plugging the cartridges (with provided half moon plugs) and using a new One Step™ mixing nozzle.
Packaging & Availability
- Regional Availability
- Packaging and Coverage
Millennium Hurricane Force® Lap and Flashing Adhesive is available in the following package:
Cartridge Size Case Part # Cartridges 1.5 Liter HF-LF15-04 4 Each cartridge will produce approximately of 50 - 75 lineal feet (15m - 23m) of 3/4” - 1” (1.9cm - 2.5cm) wide adhesive beads. Coverage rates may vary when used over irregular surfaces.
Storage & Handling
- Storage Conditions
Keep temperature of contents between 65°F to 85°F (18°C to 29°C) 24 hours prior to use. Do not store in direct sunlight or temperatures higher than 90°F (32°C).