Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
- Features and Benefits
- High Strength
- Highly Resistant to Heat, Corrosion, and Vibrations
- Highly Resistant to Water, Gasses, Oils, Hydrocarbons, and Many Chemicals
- Prevents Fasteners from Loosening
- Prevents Rust and Corrosion
Applications & Uses
- Markets
- General Instructions
Surfaces to be bonded should be clean and dry and free of grease. Product should be applied in enough quantity to fill all engaged threads or gap. The product performs best in thin bond gaps. Very large gaps may create gaps that will affect the cure speed and overall strength. Good contact is essential. Flanges should tightened as soon as possible after assembly to avoid shimming. It is recommended to confirm compatibility of the product with all substrates prior to use. This product is not recommended for use with strong oxidizing materials. Where aqueous washing systems are used to clean the surfaces before bonding, these aqueous washes can affect the cure and performance of the adhesive. This product is not normally recommended for use on plastics, users must check compatibility of the product with such substrates.
Properties
- Color
- Chemical Resistance
- Cured Properties
- Uncured Properties
- Specifications
MIL-S- 46163, Type 1, Grade K
| Value | Units | Test Method / Conditions | |
| Room Temperature Strength (50% Water/50% Glycol, at 87°C, 1000h) | 85.0 | % | - |
| Room Temperature Strength (Unleaded gasoline, at 22°C, 1000 h) | 95.0 | % | - |
| Room Temperature Strength (Motor oil, at 125°C, 1000 h) | 75.0 | % | - |
| Room Temperature Strength (Brake fluid, at 22°C, 1000h) | 100.0 | % | - |
| Room Temperature Strength (Acetone, at 22°C, 1000h) | 95.0 | % | - |
| Value | Units | Test Method / Conditions | |
| Service Temperature | - 55 - 150 | °C | - |
| Breakaway Torque | 17 - 40 | N-m | ISO 10964 |
| Prevailing Torque | 23 - 40 | N-m | ISO 10964 |
| Coefficient of Thermal Expansion | 80.0 | ppm/K | ASTM D696 |
| Cure Speed (at 5°C, 25% of room temperature strength) | 5.0 | h | - |
| Cure Speed (at 5°C, 50% of room temperature strength) | 10.0 | h | - |
| Cure Speed (at 5°C, 100% of room temperature strength) | 24.0 | h | - |
| Cure Speed (at 40°C, 50% of room temperature strength) | 25.0 | min | - |
| Cure Speed (at 40°C, 100% of room temperature strength) | 1 - 24 | h | - |
| Cure Speed on Steel (25% of room temperature strength) | 15.0 | min | - |
| Cure Speed on Steel (50% of room temperature strength) | 40.0 | min | - |
| Cure Speed on Steel (100% of room temperature strength) | 24.0 | h | - |
| Cure Speed on Brass (25% of room temperature strength) | 20 - 24 | min | - |
| Cure Speed on Zinc Dichromate (25% of room temperature strength) | 15.0 | min | - |
| Cure Speed on Zinc Dichromate (50% of room temperature strength) | 40.0 | min | - |
| Cure Speed on Zinc Dichromate (100% of room temperature strength) | 24.0 | h | - |
| Value | Units | Test Method / Conditions | |
| Set Time (Steel) | 24.0 | h | - |
| Gap Fill | max. 0.05 | mm | - |
| Flash Point | min. 93 | °C | - |
| Viscosity | 400 - 600 | cP | - |
| Specific Gravity | 1.1 | - | - |
Technical Details & Test Data
- Curing Performance
- The rate of cure will depend on environmental conditions and the substrates used. The gap of the bond line will affect set speed. Smaller gaps tend to increase set speed. Activators may be applied to further improve set speed, but may also impair overall adhesive performance.
- Full cure condition: 24 at room temperature, or 40°C bondline temperature for 1 hour - achieve 100% of strength on steel
- Hot Strength (%RT strength, tested at temperature)
Storage & Handling
- Shelf Life
- 12 Months
- Storage Conditions
- Storage Temperature: 8 to 28°C.
- Products should be stored unopened in a cool, dry place out of direct sunlight. Products may be refrigerated for improved shelf life, but should be brought back to room temperature before use.