Tuskbond NC101 - 22L Canister

1 of 57 products in this brand
Tuskbond NC101 - 22L Canister is a non-chlorinated sprayable contact adhesive developed to bond a wide variety of substrates. It has excellent grab and a long open time, providing a strong and permanent waterproof bond.

Product Type: Contact Adhesive

Compatible Substrates & Surfaces: Expanded Polystyrene (EPS), Fibers & Fabrics, Foam, Foils, Medium-Density Fibreboard (MDF), Metal, Mineral Fiber, Plywood

Application Method: Spray

Features: Fast Grab, Good Bonding Strength, Heat Resistance, Long Open Time, Temperature Resistance, Waterproofing

  • TypeDocument Name
View All Documents

Enhanced TDS

Identification & Functionality

Features & Benefits

Applications & Uses

Markets
Applications
Application Method
Compatible Substrates & Surfaces
Guidelines for Use

Preparation: (22 L Canister)

  • Use in a well Ventilated Area.
  • Surfaces to be bonded should be clean, dry and dust free.
  • Once the hose and gun has been attached to the canister, open thevalve fully. Check the connection points for leaks at this time.
  • On first use, the canister may initially take a few seconds to spray correctly. Spray initially onto on a scrap surface to ensure the spray pattern is correct for the application. The trigger restrictor on the gun can be used to set the spray to the required width.

Application:

  • Hold the gun at 90° to the surface, approximately 4-6 inches away and apply a uniform coat of adhesive to both substrates.
  • Apply adhesive in 4-6 inch bands overlapping each band by roughly 50%, with a double coat applied to the edges. Move at a steady pace that provides an even coat of adhesive without allowing any material to puddle. Spray one surface vertically the other horizontally. For most applications, 80-100% adhesive coverage is required for full bond strength. On porous materials, a second coat of adhesive may be necessary.
  • Allow the solvents to evaporate from the adhesive (3-5 minutes depending on ambient temperature). To know when the adhesive is ready to bond, it should not transfer to a gloved hand when touched and should feel dry. Bonding the substrates before the solvents have been allowed to evaporate can cause solvent entrapment resulting in bond failures.
  • Bring the two substrates together and apply a uniform pressure over,the work piece, starting in the middle and working outwards. Pay particular attention to the edges.
  • Full cure will take 24 hours.

Properties

Physical Form
Appearance
Clear
Typical Properties
ValueUnitsTest Method / Conditions
Application Temperature15 - 25°C-
Temperature Resistant95.0°C-
Open Time1.0hour-
Drying Time3 - 5minutes-
Cure Time24.0hours-
Coverage100.0-
Coverage500.0-
Solids Content30.0%-
Storage Temperature15 - 35°C-

Packaging & Availability

Country Availability
Regional Availability
  • Africa
  • Europe
  • India
  • Middle East
Packaging Size

Available Sizes:

  • 22L, 110L Canister

Storage & Handling

Shelf Life
12 months
Disposal Information
  • Once the aerosol is empty of any hazardous materials and depressurised, it can be considered as scrap metal, in accordance with the national or local waste company, under code EWC 15 01 04* (empty aerosol, non-hazardous residues).
  • Canisters and aerosols that are still pressurised and contain product should be disposed of in accordance with the national or local waste company under code EWC 16 05 04* (full or partially empty aerosol).
Storage & Shelf Life
  • Protect from extremes of temperature in a controlled environment between 15 and 35°C, and away from direct sunlight. Do not stand on a cold concrete floor. Low temperatures can result in irreparable separation of the adhesive.
  • Stored under the correct conditions, in original. unopened containers, the product will have a shelf life of 12 months. The adhesive will have a limited life once the container is opened.