H.B. Fuller

Identification

GBU: BAS
RTU Product Type: Waterborne Coating,

Encapsulant

Categories: Markets → Building & Construction → Applications → Building Materials → Pipes & Plumbing

Markets → Industrial → Applications → Chemical & Industrial Manufacturing → Equipment & Parts

Technologies → Adhesives & Sealants → Product Families → Functional Adhesives → Encapsulants

Technologies → Ready-to-Use Products → Product Families → Paints & Coatings → Other Paints & Coatings

Applications

Application Area: Pipes,

Pipe Fittings,

Equipment,

Ductwork,

Air Ducts
Application Method: Brush,

Spray

Applications & Uses

Cleaning Information

Use fresh water to clean equipment before the product dries.
Dry product may be removed with hot soapy water or strong solvents such as chlorinated solvent (non-flammable) or xylol (flammable).

Preparation and Application Information

Material Preparation

Use Chil-Bridge™ CP-211 as supplied.
Do Not Dilute or Thin.
Store at room temperature 25°C prior to application to achieve best results.
Keep from freezing.

Spray Application

Chil-Bridge™ CP-211 coating may be sprayed with many types of equipment, including airless spray.
It may also be sprayed with conventional mastic spray equipment using an external atomizing spray gun.
For best results, foster recommends the following airless spray equipment.
Average viscosity range: 100,000-130,000 cps.
Pump: Graco bulldog hydramastic, 40:1 ratio (model 204-925) air regulator with inductor plate (207-039).
Compressor: Capable of 75 cfm and maintaining 100 psig.
Fluid hose: High pressure capable of 4,000 psi. One inch up to 150 feet. 3/4 inch after the first 150 feet. Use 8' (2.4 m) 1/2" I.D. Hose for coupling to the gun.
Gun: Graco hydra-mastic #207-300 with reverse-a-clean 205-614. Tip sizes: 635 to 655.

Features

Ready-to-Use Product Features: Durable,

Good Bonding Strength,

Good Toughness,

Water-based,

Mechanical Stability

Features & Benefits

Labeling Claims

Lead-free,

Asbestos-free,

Mercury-free

Product Highlights

Chil-Bridge™ CP-211 bridging encasement/encapsulant coating is applied over ACM when bridging encapsulation has been determined to be the most appropriate asbestos abatement control method, and when complete removal of asbestos containing materials is not practical due to inaccessibility or other existing limitations.
Chil-Bridge™ CP-211 bridging encasement/encapsulant coating is applied to previously encapsulated ACM on piping, fittings, ductwork, and equipment.
Chil-Bridge™ CP-211 bridging encasement/encapsulant coating seals and bonds to ACM and to adjacent surfaces and materials.
Once dry, the resultant film is tough, durable, and pliable; it will prevent damage due to mechanical abuse in the removal efforts, which could allow asbestos fibers to become airborne. The encasement/encapsulant coating permits ACM to be handled more efficiently and safely.
Chil-Bridge™ CP-211 meets the requirements of NFPA 90A and 90B 25/50 requirements.
Meets requirements for LEED IEQ 4.2 Low-Emitting Materials, Paints and Coatings.

Packaging & Availability

Regional Availability

North America

Physical Properties

Color (Properties): Blue
Physical Form: Liquid

Properties

Shelf Life:

6 months

Note

¹- Applied to 1/4 inch (6.4 mm) inorganic, reinforced cement board at a coverage rate of 6 galllons/100 sq. ft. (2.44 liters/sq. m). The flame spread may vary at different product thicknesses and/or when applied over surfaces other than inorganic, reinforced cement board.

Application Properties


	Value	Units	Test Method / Conditions
Application Temperature	4 - 93	°C	-
Service Temperature Range	-29 to 93	°C	FSTM 70

Flame Characteristics


	Value	Units	Test Method / Conditions
Smoke Developed¹	40	-	ASTM E84
Surface Flame Spread¹	10	-	ASTM E84

Typical Properties


	Value	Units	Test Method / Conditions
Average Non-Volatile Content	66	Vol(%)	ASTM D-1644
Average Non-Volatile Content	74	Wt(%)	ASTM D-1644
Coverage Range	2.4	gal./100 sq. ft	-
Density	10.9	lbs/gal	ASTM D1475
Drying Time (through)	24 - 36	hours	-
Drying Time (to touch)	2	hours	ASTM D-1640
Flash Point (wet flammability)	99	°C	ASTM D3278
Storage Temperature	max. 38	°C	-
Volatile Organic Compound Content	40	g/L	-

Regulatory & Compliance

Certifications & Compliance: LEED (Leadership in Energy & Environmental Design),

National Fire Prevention Association (NFPA),

UL Certified
Chemical Inventories: AICS (Australia),

DSL (Canada),

ENCS (Japan),

IECSC (China),

PICCS (Phillipines),

TSCA (USA),

TSCA Exempt (USA)
Quality Standards: NFPA 90A,

NFPA 90B

Storage & Handling

Handling Conditions

Protect from freezing until dry. Do not store over 100°F (38°C).
Do not apply below 40°F (4°C) or to surfaces operating at, or intended to operate in, excess of 200°F (93°C) .
Not recommended for outdoor horizontal surfaces having a pitch of less that 1/2 inch (4 cm/m) per lineal foot.
Not suggested for use on floors.

Shelf Life