Millennium EPDM Semi-Cured Cover Strip
1 of 36 products in this brandRTU Product Type: Tape
Application Area: Fasteners, Membranes, Pond Linings, Roofing Substrates, Roofs
Features: Excellent Substrate Adhesion, Good Green Strength, Heat Resistance, High Durability, Moisture Resistant, Resistance to UV lights
Enhanced TDS
Identification
- Backing Material
- GBU
- RTU Product Type
- Categories
Applications
- Application Area
- Segment
Applications & Uses
- Application Method
-
1. Clean entire surface where Millennium EPDM Cover Strip will be applied.
2. Apply Millennium Single-Ply Primer or Millennium Primer 240 (LVOC) to entire surface to be covered using the supplied scrub pad. NOTE: Use caution when installlling at temperatures below 40°F (4°C) to prevent blushing of EPDM primer (formation of condensation on surface of primer).
3. Allow the primer to dry to the touch (no material transfer, typically less than 20 minutes). Dry time will vary depending on ambient temperature and humidity.
4. Once the primer is dry immediately install Millennium EPDM Cover Strip.
5. Position Cover Strip over primed area and remove release liner at 45 degree angle while pressing down cover strip by hand.
6. Roll the Cover Strip with a 2” (5.08cm) wide silicone roller. 7. Seal edges of cover detail with patented Millennium EPDM Edge Sealant.*
*US 6,642,296 B2; US 6,291,571 B1
- Basic Use
-
Millennium EPDM Cover Strips are designed to cover, protect, and seal mechanical fastening bars, membrane fasteners, core sample repair patches, membrane repairs, metal edge tie-in, and seam overlays in all EPDM roofing systems.
- Limitations
-
- Not for use on PVC roof membranes.
- Talc, dust, oil, ice, snow, or wet conditions inhibit good adhesion.Clean and dry surfaces are necessary for proper Installation of this product.
- Note
-
The foregoing information is published as general information only. The listed properties and performance characteristics are typical values and are not to be interpreted as manufacturing specifications.
- Surface Preparation
-
All work surfaces should be clean, dry, and free of dirt, dust, debris, oils, un-adhered coatings, deteriorated membrane and other contaminants that may result in a surface that is not sound or is uneven. If necessary, clean the surface to receive the flashing with an approved EPDM membrane cleaner.
Features
- Ready-to-Use Product Features
Features & Benefits
- Key Attributes
-
Features Benefits Resistant to UV light, high heat and moisture Long-term durability
Excellent adhesion to multiple substrates Suitable for a wide variety of sealing applications
No torch or liquid adhesives Improved safety Fast Installation Saves time and labor
Waterproof detail Suitable for roofing, pond lining, and waterproofing applications
Identification & Functionality
- Base Polymer (Cover & Tape)
-
- Base - EPDM
- Test Method - FTIR
- Product Image
-
Packaging & Availability
- Packaging Type
- Regional Availability
- Packaging and Coverage
-
Millennium EPDM Seam Tape is available in the following sizes:
North America
Width Length Part # Rolls/Case 5 inch (127mm) 100 ft. (30.48m) ET-0911-05CC 2 6 inch (152mm) 100 ft. (30.48m) ET-0911-06CC 2 9 inch (229mm) 100 ft. (30.48m) ET-0911-09CC 1 12 inch (305mm) 50 ft. (15.24m) ET-0911-12CC 1 18 inch (457mm) 50 ft. (15.24m) ET-0911-18CC 1 Europe , CIS and Middle East
Width Length Part # Rolls/Case 5 inch (127mm) 100 ft. (30.48m) ET-0911-05EU 2 6 inch (152mm) 100 ft. (30.48m) ET-0911-06EU 2 9 inch (229mm) 100 ft. (30.48m) ET-0911-09EU 1 12 inch (305mm) 50 ft. (15.24m) ET-0911-12EU 1 18 inch (457mm) 50 ft. (15.24m) ET-0911-18EU 1
Physical Properties
- Color (Properties)
Properties
- Shelf Life:
-
24 months
- Strain at Break:
-
300 %
- Tensile Strength:
-
6.21 MPa
- Typical Physical Properties
-
Value Units Test Method / Conditions Brittle Point -46 °C ASTM D2137 Elongation 300 % ASTM D412 Ozone Resistance No cracking - ASTM D4419 Peel Strength (at 21°C) 10 pli ASTM D413 Shear Strength (at 21°C) 20 psi ASTM D816 Tear Strength 125 lb/in ASTM D624 Tensile Strength (die c) min. 900 psi ASTM D412 - Typical Properties
-
Value Units Test Method / Conditions Base Polymer (cover and tape) Ethylene Propylene Diene Monomer - Fourier Transform Infrared Spectroscopy Storage Temperature 40 - 110 °F -
Storage & Handling
- Storage Conditions
-
Store material in original unopened packaging at temperatures between 40°F-110°F (4°C - 43°C). Shelf life is 24 months when stored as recommended.
- Shelf Life
-
24 months