Foster® Duct-FAS™ Duct Sealant 32-19™
1 of 39 products in this brandRTU Product Type: Waterborne Sealant
Application Area: Joints
Compatible Substrates & Surfaces: Aluminum, Metal
Application Method: Brush, Trowel
Features: Fire-Resistant, Flexible, UV Resistant
Enhanced TDS
Identification
- GBU
- RTU Product Type
- Categories
Applications
- Application Area
- Application Method
- Compatible Substrates & Surfaces
Applications & Uses
- Limitations
-
- To resist rain washoff, allow at least 16 hours drying time above 40o°F(4°C), with a relative humidity of 50%. Higher humidity or lower temperatures may retard drying.
- Always test foil and paper facings for acceptable adhesion.
- Outdoor horizontal surfaces must always drain completely. A pitch of at least 1/2 inch per foot (4 cm/m) is required.
- If used between impermeable surfaces, drying time will be extended.
- Preparation and Application Information
-
Material Preparation
Do not thin. Apply only to clean, dry, oil-free surfaces. Keep container closed when not in use.
Application
UL 181B mastic closure of UL 181 flexible ducts: Apply to clean, dry, oil-free surfaces by brush, trowel or power extrusion. Uniformly brush out a 2” wide coat over the joint, at the nominal rate of 2 gal./100 sq. ft.. Total coverage rate to be 45 - 55 sq. ft./gal. Allow the completed joint to dry at least 24 hours above 70°F before pressure testing. High humidities (over 70%) and/or cooler temperatures may retard drying. Total wet film thickness to be 32 mils +/- 3 mils.
Other Sealing Applications – Not UL 181
Apply a continuous film of Duct-FASTM Duct Sealant over all areas of the indoor or outdoor duct system where air leakage may occur. A brush may be used to work the sealant into joints and remove excess. On spiral ducts, apply a coat of Duct-FAS™ Duct Sealant to the male end of the coupling prior to fitting the straight run of spiral duct over it. Brush excess Duct-FAS™ Duct Sealant over the joint to complete the seal. Screw holes and flanges should also be sealed with a coat of Duct-FAS™ Duct Sealant . It may be applied to the inside or the outside of the duct.
Power Extrusion
Duct-FAS™ Duct Sealant may be applied using a wide variety of power (pressure) extrusion equipment suitable for use with water-based sealants. It is a soft buttery gel with a typical viscosity range of 130,000 - 160,000 cps. Corrosion resistant pumps and fittings are suggested.
Top Coating
After it is completely dry, Duct-FAS™ Duct Sealant may be top coated with good quality water-based paint.
Clean Up
Use fresh water to clean brushes and equipment before product dries. Dry product may be removed with hot soapy water or strong solvents such as chlorinated solvent (non-flammable) or xylol (flammable).
Features
- Ready-to-Use Product Features
Features & Benefits
- Product Highlights
-
- Foster® Duct-FAS™ Duct Sealant 32-19™ may be pressure tested after 24 hours dry time above 70°F (21°C). It quickly forms a strong bond to clean galvanized, aluminum and mild steel metal ducts.
- Foster® Duct-FAS™ Duct Sealant 32-19™ is ideal for sealing ASJ, FRK and FSK jackets and board facings at joints, laps and over staple and weld pin punctures, and for sealing flexible air ducts to rigid connectors.
- Foster® Duct-FAS™ Duct Sealant 32-19™ will meet all SMACNA pressure classes up to 10" w.g. and SMACNA seal classes A, B and C on ducts constructed to SMACNA standards. It has been tested up to 15" w.g. and passed with no sealant blow out.
Packaging & Availability
- Regional Availability
Physical Properties
- Color (Properties)
- Physical Form
Properties
- Note
-
¹ - Tested as applied in two 2 in. wide strips spaced 8 in. on center at a coverage rate of 45 sq. ft./gal. Applied to 1/4 inch (6.4 mm) inorganic reinforced cement board. The flame spread may vary at different product thicknesses and/or when applied over other surfaces.
- Application Properties
-
Value Units Test Method / Conditions Service Temperature Range -7 to 93 °C - - Flame Characteristics
-
Value Units Test Method / Conditions Flame Spread¹ 0 - ASTM E 84 Smoke Developed¹ 0 - ASTM E 84 - Typical Properties
-
Value Units Test Method / Conditions Average Non-Volatile Content 56 Vol(%) ASTM D2369 Average Non-Volatile Content 70 Wt(%) ASTM D2369 Coverage (brush, 0.8 mm wet film thickness) 50 ft²/gal - Coverage (caulking gun, 1/4 inch bead) 30 linear ft. per 10.5 fluid oz. tube - Coverage (caulking gun, 1/8 inch bead) 125 ft./10.5 fluid oz. tube - Density 11.7 lbs/gal ASTM D1475 Drying Time (at 23°C, 50% RH, set to touch) 1 hour - Drying Time (at 23°C, 50% RH, through dry) 16 hours - Flash Point (wet flammability) 99 °C - Fungal Growth Resistance 0 rating ASTM G21 Hardness 72 Shore A ASTM D2240, Shore Durometer Scale Storage Temperature 4 - 38 °C - Volatile Organic Compound Content 24 g/L -
Regulatory & Compliance
- Certifications & Compliance
- Chemical Inventories
Storage & Handling
- Storage Condition
-
Store and apply between 40°F and 100°F, protect from freezing until dry.
- Shelf Life
-
12 months