H.B. Fuller 2150

H.B. Fuller 2150 is a single-component, high-viscosity cyanoacrylate adhesive with a quicker setting speed than most high-viscosity materials. It is suitable for all general-purpose bonding and is certified to ISO 10993-5 for biocompatibility, making it suitable for use in medical applications.

Product Type1K (1 component) Adhesive, Reactive Adhesive

Application AreaMedical Devices

Chemical FamilyCyanoacrylates

FeaturesChemical Resistant, Fast Setting, General Purpose, Good Solvent Resistance, High Viscosity

Technical Data Sheet

Enhanced TDS

Identification & Functionality

Chemical Family

Features & Benefits

Applications & Uses

Application Area
Cure Method
General Instructions

Surfaces to be bonded should be clean and dry. Dispense a drop or drops to one surface only. Apply only enough to leave a thin film layer after compression. Press parts together and hold firmly for a few seconds. Good contact is essential. An adequate bond develops in less that one minute and maximum strength is attained in 24 hours. Wipe off excess adhesive from the top of the container and recap. products if left uncapped may deteriorate by contamination from moisture in the air. Because products cure by polymerization, whitening may appear on the surface of the container or the bonded materials. This will not affect adhesive performance.

Properties

Appearance
Clear
Technical Data
ValueUnitsTest Method / Conditions
Specific Gravity1.06
Cured Properties
ValueUnitsTest Method / Conditions
Service Temperature- 55 - 95°C
Full Cure Time24.0h
Cure AppearanceClear
Uncured Properties
ValueUnitsTest Method / Conditions
Flash Point85.0°C
Set Time (Ethylene Propylene Diene Monomer)10.0s
Set Time (Steel)40.0s
Set Time (Acrylonitrile Butadiene Styrene)9.0s
Rheological Properties
ValueUnitsTest Method / Conditions
Viscosity1500 - 2100cP
Specifications

Mil-A-46050C, Type II Class III, A-A-3097, Type II Class 3

Regulatory & Compliance

Certifications & Compliance

Technical Details & Test Data

Performance of Cured Adhesive
Substrate N/mm² PSI
Steel 13.8 to 20.1 2000 to 2920
Rubber* 4.3 to 15.2 630 to 2200
AL 12.6 to 15.8 1830 to 2290
PC** 17.9 to 22.9 2590 to 3320
PVC** 14.2 to 23.4 2065 to 3400
ABS** 15.1 to 16.4 2185 to 2375

 

*Rubber figures given are typical. Your results may vary by specific rubber type.
**Tested to ASTM 4501
***n/r = not recommended

Curing Performance

Ambient surface moisture initiates the curing process. Handling strength is reached in a short time, and will vary based on environmental conditions, bond line gap, and other factors. Product will continue to cure for at least 24 hours before full strength and solvent resistance is developed.

Time Until Full Cure (% of RT strength)

H.B. Fuller 2150 - Time Until Full Cure (% of Rt Strength)

Performance Range by Substrate (N/mm²)

H.B. Fuller 2150 - Performance Range By Substrate (N/Mm²)

Heat Aging (aged at temperature indicated and tested at 22°C)

H.B. Fuller 2150 - Heat Aging (Aged At Temperature Indicated And Tested At 22°C)

Hot Strength (%RT strength, tested at temperature)

H.B. Fuller 2150 - Hot Strength (%Rt Strength, Tested At Temperature)

Solvent Resistance
Solvent Example Resistance
Alcohol

Ethanol, Methanol

+ + +
Ester (aromatic) Ethylacetate + + +
Ketone (aromatic)

Acetone, Benzophenone

– – –
Aliphatic hydrocarbon (alkanes)

Petrol, Heptanes, Hexane

+ + –
Aromatic hydrocarbons

Benzyl, Toluol, Xylol

+ + –
Halogenated hydrocarbons

Methylenchloride, Chloroform, Chlorobenzol

– – –
Weak aqueous

Nitrite, muriatic acid, sulphuric acid, phosphoric acid

+ + + (– – – if concentrated)
Weak aqueous base

sodium hydroxide solution, caustic potash

+ + + (– – – if concentrated)

Storage & Handling

Shelf Life
12 Months
Storage Conditions

Containers should be stored in a cool, dry, dark area. Storage temperature 15.5°C - 25°C (60°F - 77°F), without exposure to direct light or heat. Do not refrigerate.