Millennium Hurricane Force® 1-Part Flashing Adhesive
1 of 33 products in this brandChemical Family: Urethanes
RTU Product Type: 1K (1 component) Adhesive, Elastomeric Adhesive, Reactive Adhesive, Solvent free (100% Solids) Adhesive
Application Area: Roofing Substrates
Application Method: Trowel
Compatible Substrates & Surfaces: Concrete, Fiberglass, Gypsum, Masonry, Metal, Wood
Features: Flexible
Enhanced TDS
Identification
- Chemical Family
- GBU
- RTU Product Type
- Categories
Applications
- Application Area
- Application Method
- Compatible Substrates & Surfaces
Applications & Uses
- Application Method
-
1. Ensure that the substrate is suitable for bonding and is clean, dry, and free of defects.
2. Apply Hurricane Force® 1-Part Flashing Adhesive with a 1/4” (0.6 cm) notched trowel directly to the backside of the flashing membrane (as shown) or to the bonding substrate.
3. Embed the flashing membrane into the freshly applied adhesive. Do not allow the adhesive to skin over. Apply pressure across the entire membrane surface to ensure full contact with the adhesive removing all wrinkles and air pockets.
4. A continuous bleed-out of adhesive should be present along all membrane side laps and tie-ins.
5. For multi-layer flashing applications repeat steps 2-4.
- Approved Substrates
-
- Concrete
- Cinder and masonry block
- Base sheets (sanded or
- granule surfaced)
- Plywood
- Metal
- Fiberglass insulation
- Polyisocyanurate insulation
- Perlite insulation
- Wood fiber insulation
- Polystirene (XPS, EPS)
- Gypsum Cover board
- High density polyisocyanurate cover board
Approved Membranes
- SBS modified bitumen base sheets
- SBS modified bitumen mineral surfaced cap sheets
- Basic Use
-
Millennium Hurricane Force® 1-Part Flashing Adhesive is specially formulated for use as a vertical grade flashing adhesive for bonding approved base sheets, vapor retarders and membranes for low slope roof applications. Millennium Hurricane Force® 1-Part Flashing Adhesive can also be used to seal head laps in modified bitumen roof membranes.
Millennium Hurricane Force® 1-Part Flashing Adhesive forms a strong bond to most substrates and does not soften or damage the membrane.
- Limitations
-
- Do not apply to wet or damp surfaces. This includes primers.
- Allow solvent based primers to completely dry before using the adhesive.
- Do not apply when surface temperatures are below 40°F (4°C).
- Surface Preparation
-
All work surfaces should be clean, dry, and free of dirt, dust, debris, oils, un-adhered coatings, deteriorated membrane or other contaminants that may result in a surface that is not sound or is uneven.
Features
- Ready-to-Use Product Features
Features & Benefits
- Key Attributes
-
Features Benefits Single component Requires no mixing
Solvent free No odors Elastomeric Remains flexible, absorbs stresses
VOC content less than 250 g/L Suitable for use in VOC regulated markets
Cold applied Won’t burn, no exposure to oxidized asphalt fumes
Identification & Functionality
- Product Image
-
Packaging & Availability
- Packaging Type
- Regional Availability
- Packaging and Coverage
-
Millennium Hurricane Force® 1-Part Flashing Adhesive is available in the following package:
Pails Size Part # Pails/Case 5 Gallon (18.9L) HF-FA5P-01 36 Coverage rate is approximately 12-15 sq. ft. (1.1-1.4 m2) per gallon when applied with a 1/4” notched trowel which results in an approximately 1/8” (0.3 cm) thick layer of adhesive.
Coverage rates may vary when used over irregular surfaces.
Physical Properties
- Color (Properties)
Properties
- Shelf Life:
-
9 months
- Typical Properties
-
Value Units Test Method / Conditions Application Temperature min. 40 °F - Storage Temperature 15 - 27 °C - Volatile Organic Compound Content max. 250 g/L -
Storage & Handling
- Storage Conditions
-
Store material in original unopened packaging at temperatures between 40°F-100°F (4°C-38°C). For best results store material at temperatures between 60°F-80°F (15°C-27°C) just prior to use. Shelf life is 9 months when stored as recommended.
- Shelf Life
-
9 months