H.B. Fuller

Applications & Uses

Clean Surface

The surface condition of the mating parts has an enormous influence on the success of a bond. To achieve good bonding success the mating parts should be clean.

LINOP Equipment

Cyberbond offers by means of the LINOP Equipment range suitable dosing and LED based curing devices. We also refer to suitable dosing tips which help an economical use of the adhesives (also if used manually).

Solvent Resistance

Solvent	Resistance	Example
Alcohol	Excellent	Ethanol, Methanol, Isopropanol
Aliphatic hydrocarbons (alkanes)	Very good	Petrol, Heptanes, Hexane
Aromatic hydrocarbons	Very good	Benzyl, Toluol, Xylol
Ester (aliphatic)	Poor	Ethyl acetate
Halogenated hydrocarbons	Poor	Methylene chloride, Chloroform, Chlorobenzene
Ketone	Poor	Acetone, Benzophenone
Weak aqueous acid	Excellent	Diluted nitrite, muriatic acid, sulfuric acid, phosphoric acid
Concentrated acid	Poor	Nitric acid, muriatic acid, sulfuric acid, phosphoric acid
Weak aqueous base	Excellent	Diluted sodium hydroxide solution, caustic potash solution
Concentrated base	Poor	Sodium hydroxide solution, caustic potash solution
Water	Very good

Features

Ready-to-Use Product Features: Alcohol Resistant,

Fast Setting,

Good Adhesion,

Good Gap Filling Capabilities,

Low Odor,

Medium Viscosity,

Water Resistant,

Improved Ageing Resistance,

Solvent Resistance,

Fast Bonding

Features & Benefits

Product Highlights

Cyanoacrylates are fast setting, one component and solvent free adhesives. They are based on esters of cyanoacetic acid. To get to a finished product, mainly thickeners, respectively film forming agents (polymer methacrylics and acrylics) and stabilizers are added. The polymerization is initiated by present humidity. Best results are given between 40 to 70 % relative humidity.

Cyberbond standard grades are as follows:

Powerdrop series (stabilized ethyl ester)
Elastomer and plastic series (ethyl ester)
Neomer Series (surface insensitive ethyl ester)
xtraflex series (rubber toughened ethyl ester)
metal series (ethyl ester)
low odor series (alkoxy ester)
medical series (butyl- and octyl ester)

Identification & Functionality

Base Compound: Ethyl - 2 - cyanoacrylate

Packaging & Availability

Regional Availability

Asia Pacific
Europe
North America
Latin America
India/MiddleEast/Africa (IMEA)

Physical Properties

Physical Form: Liquid

Properties

Density:

1050 kg/m³

Flash Point:

85 °C

Shelf Life:

12 months

Specific Gravity:

1.05

Viscosity:

65~200 cps

Physical Properties


	Value	Units	Test Method / Conditions
Density	1.05	g/cm³	-
Flash Point	82.5	°C	-
Service Temperature Range	-55 to 95	°C	-
Set Time (Acrylonitrile Butadiene Styrene)	2 - 4	seconds	-
Set Time (Ethylene Propylene Diene Monomer)	2 - 4	seconds	-
Set Time (metal - steel)	20 - 50	seconds	-

Uncured Properties


	Value	Units	Test Method / Conditions
Density (at 20°C, uncured)	1.05	g/cm³	-
Flash Point	85	°C	-

Cured Properties


	Value	Units	Test Method / Conditions
Strength of Cured Adhesive (Nitrile Butadiene Rubber, cured)	5 - 12	N/mm²	-
Strength of Cured Adhesive (steel, cured)	10 - 26	N/mm²	-

Typical Properties


	Value	Units	Test Method / Conditions
Viscosity (at 20°C, 160rpm)	65 - 200	cPs	Cone-Plate Viscometer

Processing Parameters


	Value	Units	Test Method / Conditions
Viscosity (at 158 1/s, cone-plate, 20°C)	65 - 200	mPa·s	-

Regulatory & Compliance

Certifications & Compliance

ISO 10993

Specification

ISO 10993-5: Tests for in vitro cytotoxicity (biocompatibility).
ISO 10993-10: Tests for iritation and delayed-type hyper-sensitivity.
ISO 10993-11: Tests for systematic toxicity.
RoHS conform

Safety & Health

Potential Danger of Cyanoacrylates

You should care for the following:

Use in well ventilated areas only
Installll suitable exhaust systems in the workshop
Apply material economically and use a dosing system where appropriate
Allow a consistent relative humidity of 50 to 65 %; with regards to lower figures the polymerization will be delayed and monomer adhesive fume will appear
If necessary: wear suitable, non-sucking gloves (Eg. No cotton)
Keep adhesive out of reach of children

The data mentioned in this TDS, particularly the recommendations and use of products are based on our recent knowledge and experience. Due to the fact of having so many different materials involved and conditions of applications which are out of our influence, we strongly recommend to do sufficient tests in order to guarantee that Cyberbond products are suitable for the intended process and applications. Except for wilful acts any liability based on such recommendations or any verbal advice is hereby expressly excluded.

Storage & Handling

Storage Conditions: Cyberbond® 2011 should be used within the shelf life specified on the packaging. The storage stability applies to material stored under appropriate conditions only (original unopened containers, recommended storage temperature). This product should be stored unopened in a cool, dry place out of direct sunlight. Refer to the Technical Data section of this document for optimum storage temperatures.
Shelf Life: 12 months (at 20°C, unopened), 12 months (unopened, < 20°C)

Technical Details & Test Data

Measurement of Viscosities

Viscosity describes the flow-ability of a liquid. Cyberbond measures the viscosity of the products by means of the cone/plate method: the liquid is applied on a panel and a defined cone presses the liquid together and rotates. You differentiate between a Newtonian and a thixotropic liquid. In terms of a Newtonian liquid you will get a relative constant viscosity graph in dependence of the rotary speed of the cone. In terms of thixotropic liquids the product becomes more liquid (down to its base viscosity) the faster the cone rotates. The viscosity is measured in mPa*s (milli Pascal x second) [SI system] or in cP (centipoise) [CGS- system]; 1 mPa*s = 1 cP. In order to allow products comparison all adhesives are measured at the same rotation speeds.

Newtonian liquids at 160 upm
Thixotropic liquids at 0,5 upm and at 160 upm

Temperature always is at 20 °C / 68 °F, if not mentioned to be different.

Technical Details

Hot Strength on Steel

% of RT strength, tested at temperature.

Cyberbond CB 2011 - Technical Details

Time Until Full Cure

% of RT strength

Cyberbond CB 2011 - Technical Details - 1

Strength of cured adhesive

Substrate	N/mm2
NBR-rubber ▲	5 to 12
steel	10 to 26

▲ material failure

Cyberbond CB 2011 - Technical Details - 2

Heat Aging - on Steel

Tested at 20°C

Durability after Storage under Changing Climatic Conditions

Processing

Surfaces should be clean and free from grease. Dispense adhesive to one surface only. Apply only enough to leave a thin film layer after compression. Press parts together and hold firmly until adhesive has fixtured. Maximum strength is attained typically in 24 hours. Product should be allowed to develop full strength before subjecting to any service loads.

Cyberbond CB 2011

Enhanced TDS

Identification

Application Information

Applications