Cilbond® 89ET
1 of 11 products in this brandApplication Method: Brush, Dip Coating, Spray
Compatible Substrates & Surfaces: Butadiene Rubber (BR), Carboxylated Nitrile Butadiene Rubber (XNBR), Chlorinated Polyethylene (CPE), Chloroprene Rubber (CR), Chlorosulfonated Polyethylene Synthetic Rubber (ACSM), Elastomers & Rubbers, Epichlorohydrin Rubber (ECO), Ethylene Acrylic Rubber (AEM), Ethylene Propylene Diene Monomer (EPDM), Ethylene Propylene Rubber (EPM), Ethylene Vinyl Acetate (EVA), Glass Fibre Reinforced Polymer (GFRP), Hydrogenated Acrylonitrile Butadiene Rubber (HNBR), Isobutylene Isoprene Rubber (IIR), Isoprene Rubber (IR), Metal, Natural Rubber, Nitrile Butadiene Rubber (NBR), Plastics, Polyacrylate Rubber (ACM), Polyamide, Polyesters, Polyurethane, Styrene Butadiene Rubber (SBR), Thermosetting Plastics
Features: Boil Water Resistance, Chemical Resistant, Easy To Apply, Excellent Adherence, Excellent Salt Spray Resistance, Fatigue Resistant, Fuel Resistant, Good Glycol Resistance, Good Hot Oil Resistant, Grease Resistant, Heat Resistance, Highly Versatile, High Performance, Low Temperature Resistant, Minimal Mould Build Up, Oil Resistant, Pre-bake Resistance, Solvent-Based, Water Resistant
-
Type Document Name
-
Technical Data SheetCilbond® 89ET Technical Data Sheet
Enhanced TDS
Identification
- Carrier
- GBU
- RTU Product Type
- Categories
-
Applications
- Application Area
- Application Method
- Compatible Substrates & Surfaces
-
- Segment
Applications & Uses
- Cleaning
-
Cleaner for Tools
- Toluene
- Xylene
- Processing Information
-
Suitable Elastomers
- Natural rubber (NR)
- Styrene butadiene rubber (SBR)
- Chloroprene Rubber (CR)
- Polybutadiene (BR)
- Synthetic polyisoprene rubber (IR)
- Polyepichlorohydrin (ECO)
- Polyacrylate rubbers (ACM)
- Chlorosulphonated polyethylene (CSM / ACSM)
- Carboxylated NBR (XNBR)
- Ethylene vinyl acetate EVA (EVM)
- HNBR
- IIR
- EPDM
- Millable polyurethane (PU)
- Chlorinate polyethylene (CPE)
- Halogenated butyl rubber (CIIR or BIIR)
- NBR
- Hot cast polyurethane (PU)
Suitable Substrates
- Various surface treated metals
- Glass fibre reinforced plastic (GFRP)
- Various metals
- Polyamide (PA)
- Polyester (PES)
- Various other substrates
Consistency
- Liquid
Surface Requirements
- Free of rust
- Grit blasted or other approved surface treatments
- Dry
- Clean
- Free of grease
- Free of dust
- Free of oil
Application Method
- Spraying
- Dipping
- Roller coating
- Brushing
- Usage Information
-
Agitation: Cilbond 89ET must be thoroughly stirred before use, preferably with a propeller type agitator.
Brushing: Cilbond 89ET can be brush applied without the need for dilution. If dilution is required (if covering large areas) use Xylene or Toluene.
Spraying: To apply by spray, dilute with Toluene or Xylene to a viscosity of 23 - 26 seconds (Zahn No. 2 cup at 25°C) or 16 - 20 seconds on a DIN 4 / Ford 4 / Frikmar Cup at 25°C.
If cob-webbing (fibrillation) occurs on spraying, replace the Toluene with Xylene. A nozzle size of 1.0 - 1.5mm is recommended, with an air pressure of 1.5 bar.
Note : Excessive pressure can lead to cob-webbing. Cilbond 89ET contains an isocyanate prepolymer of very low volatility. This is reactive towards water and so extra care must be taken when spraying.
Dipping: For Dipping, dilute with Toluene or Xylene to a viscosity of 23 - 26 seconds (Zahn No 2 cup at 25°C) or 16 - 20 seconds on a DIN 4 / Ford 4 / Frikmar Cup at 25°C.
Dilution: CIL recommends Xylene or Toluene to dilute Cilbond 89ET.
Coating thickness: As a One-Component bonding system apply at a dry film thickness of 15 – 30 microns. As a Cover-Coat bonding system apply at a dry film thickness of 10 – 25 microns.
​​​​​​​Drying: Allow 20 - 30 minutes drying time at room temperature. Pre-warming parts to ~60°C prior to coating will reduce the drying time.
Pre-baking: Pre-baking Cilbond 89ET is not normally recommended, but short pre-bakes of up to 10 minutes at ca. 155°C can be tolerated, if necessary.
Storage: Parts coated with Cilbond 89ET should ideally be bonded within 30 hours of drying. Allowing the coated parts to air-cure for longer than 30 hours can improve substrate
adhesion and resistance to wiping (melt-flow) and mould fouling. However, depending on the elastomer, this may also result in a gradual reduction in elastomer adhesion. Tests at CIL have shown that parts coated with Cilbond 89ET may be stored for up to 14 days (in a clean, dry environment) without a reduction in adhesion, but full customer validation is recommended.
Moulding: Cilbond 89ET can be processed by all conventional moulding techniques and it exhibits good bonding within the temperature range of 70°C – 180°C.
Features
- Ready-to-Use Product Features
-
Features & Benefits
- General Properties
-
Type of Product
- Bonding agent
- Can be used with primer Cilbond 10E or Cilbond 12E
- One-coat
Curing
- Heat curing
Color
- Black
Product Benefits
- Excellent resistance against salt-spray, water immersion, boiling water, steam up to 130°C, hot oils, fuels, glycols and hydraulic fuels up to 180°C
- Resistant to various chemicals, such as petrol, oils, greases
- Excellent static and dynamic fatigue resistance
- Excellent adherence to various substrates
- Easy application
- Minimal mould fouling
- Excellent pre-bake resistance
- Can be used for post vulcanisation bonding
- Coated parts can be swaged
- Excellent heat resistance
- Excellent low temperature resistance
Packaging & Availability
- Regional Availability
Physical Properties
- Physical Form
- Appearance
-
Black mobile liquid
Properties
- Typical Physical Properties
-
Value Units Test Method / Conditions Bonding Temperature Range 70 - 180 °C - Flash Point 15 °C Abel Pensky Method Non-Volatile Solids 24 Wt(%) - Specific Gravity (at 26°C) 0.99 - - Typical Coverage (as a cover-coat) 18 m²/L - Typical Coverage (as a one-coat system) 12 m²/L - Viscosity 20 seconds No. 3 Zahn Cup - Processing Parameters
-
Value Units Test Method / Conditions Dilution (Typically add whilst product is stirring) 20 - 40 % - Drying Time (at 23°C) 30 - 45 min - Drying Time (at 60°C) 5 min - Moulding Temperature Range 70 - 180 °C - Optimum Dry Coating Thickness 13 - 25 µm for maximum environmental resistance Service Temperature - 40 to 180 °C - Storage Temperature 1 - 25 °C - Typical Coverage (20 µm Dry Coating Thickness) 12 m²/l - Viscosity (at 26°C) 20 - No 3 Zahn Cup - Physical Properties
-
Value Units Test Method / Conditions Density 0.96 g/cm³ - Flash Point 4 °C Abel Pensky Method Solid Content 24 % - - Appearance
-
Black mobile liquid
Storage & Handling
- Storage Information
-
Cilbond 89ET should be used within the shelf life specified on the packaging. The storage stability applies to material stored under appropriate conditions only (original unopened containers, recommended storage temperature).
- Shelf Life
-
12 months