Rakoll® 4654
1 of 15 products in this brandRTU Product Type: Hot Melt Adhesive, Reactive Adhesive
Application Area: Doors, Flat Lamination, Floor, Furniture, Household, Industrial Composites, Lamination, Nonwoven, Profile Wrapping, Rigid Foam, Veneering, Wood Profile Wrapping, Woodwork
Compatible Substrates & Surfaces: Acrylonitrile Butadiene Styrene (ABS), Composites, Cotton, Foils, Leather, Metal, Paper, Plastics, Polyvinyl Chloride (PVC), Wood
Application Method: Nozzle, Roller
Chemical Family: Polyurethanes (PU)
Features: Clean Running, Fast Setting, Good Adhesion, Good Bonding Strength, Good Cold Resistance, Good Processability, Good Solvent Resistance, Good Thermal Stability, High Initial Strength, Low Temperature Performance, Short Open Time, Temperature Resistance
-
Type Document Name
-
Technical Data SheetRakoll® 4654 Technical Data Sheet
-
Product CatalogH.B. Fuller Selection Guide for Profile Wrap Flat Lam
-
Product CatalogH.B. Fuller Interior Doors Selection Guide (IT-EIMEA)
-
Product CatalogH.B. Fuller Interior Doors Selection Guide (EN-EIMEA)
-
Product CatalogH.B. Fuller Interior Doors Selection Guide (DE-EIMEA)
Enhanced TDS
Identification
- Chemical Family
- GBU
- RTU Product Type
- Categories
-
Application Information
- Cure Method
Applications
- Application Area
- Application Method
- Compatible Substrates & Surfaces
Applications & Uses
- Product Applications
-
- Lower temperatures than recommended can cause higher viscosity which result in reduced bond strength and reduced wetting.
- Refer to the technical data table regarding processing parameters.
- Lower temperatures than recommended can cause higher viscosity which result in reduced bond strength and reduced wetting.
- Depending on the construction of the equipment, a continuous heating above pro- cessing temperature can cause decomposition of the adhesive.
- Tank melters should use protective gases with < 5 ppm humidity, only. Rakoll" 4654 is moisture sensitive, therefore container must be kept closed.
- Clean tools immediately after use.
- Once cured, the material can only be removed mechanically.
- Profile Wrapping
-
- Open time: Medium
- Materials: Wooden materials, plastics
- Green strength: High
- Application: Slot nozzle
- Pre heating: Yes
- Application temp: 120 - 140ºC
- Additional information: Specially recommended for low ambient temperatures
Features
- Ready-to-Use Product Features
Features & Benefits
- Labeling Claims
- Product Benefits
-
Versatile application conditions:
- Shows high initial strength and fast setting which makes the product ideal for difficult to bond substrates.
- Low application temperatures from +120°C allow bonding of more heat sensitive materials. It also potentially provides energy cost savings.
- Suitable for profiles with tight curvatures.
Temperature resistance:
- High heat resistance after complete curing up to 150°C depending on the surface materials
- Good cold resistance
Packaging & Availability
- Regional Availability
Physical Properties
- Physical Form
- Appearance
-
White solid
Properties
- Product Properties
-
Surface Requirements
- Dry
- Clean
- Free of grease
- Free of dust
- Free of oil
- Typical Properties
-
Value Units Test Method / Conditions Application Temperature 120 - 130 °C - - Technical Data
-
Value Units Test Method / Conditions Ambient Temperature 18 - 25 °C - Density 1.1 g/cm³ - Processing Temperature 120 - 150 °C - Relative Humidity 40 - 60 % - Softening Point 67 °C Ring+Ball Storage Temperature - 25 to 35 °C - Substrate Temperature 18 - 25 °C - Typical Curing Time (23°C, 50 % RH, depending on ambient temperature and relative air humidity, considerably longer at lower temperatures and low humidity) 3 - 4 d - Viscosity (140°C, Sp. 29, 10 rpm) 25000 mPa·s Brookfield - Appearance
-
Whitish Solid
Storage & Handling
- Storage Condition
-
Rakoll 4654 should be used within the shelf life specified on the packaging. The storage stability ap- plies to material stored under appropriate conditions only (original unopened containers, recommended storage temperature).
- Shelf Life
-
9 months