Foster® Drion® Contact Cement 85-75

Identification

GBU

BAS

RTU Product Type

Adhesive

Categories

Markets → Industrial → Applications → Chemical & Industrial Manufacturing → Equipment & Parts

Technologies → Adhesives & Sealants → Product Families → Bonding & Sealing Chemistry → Cementitious Adhesive & Sealants

Applications

Application Method

Brush

Applications & Uses

Coverage Range

• 150 to 200 sq. ft./gal. per surface (3.7 - 4.9 m²/l)
• 0.011 in. to 0.008 in. (0.28 - 0.20 mm) wet film thickness
• Full Coverage: Applying to both surfaces will yield 75 - 100 sq. ft. bonded surface area per gallon
• As a Lap  Adhesive: 450 - 600 linear ft. (137 - 183 m) of lap per gallon (assuming 2 in. (5 cm) wide band of adhesive at lap)

Limitations

• Store above 70°F at least 24 hours before use.
• Make certain this product is completely dry and the area free from solvent odor if food is involved.
• Always test plastic materials and painted surfaces for compatibility when using a solvent-based product.
• Do not use with flexible PVC.

Preparation and Application Information

Material Preparation

• Do not thin. Stir well, but do not use sticks or boards which would splinter or otherwise contaminate the product. Apply only to clean, dry surfaces that are free from dust, dirt and oil. Keep container closed when not in use.

Application

• Lap and Tape Sealing:
  • Use clean paintbrush of good quality. Apply a liberal, uniform coat of DRION® CONTACT CEMENT at 150 - 200 sq. ft./gal. (3.7 - 4.9 m²/l) to both mating surfaces to be bonded and allow to dry to the touch. Under normal conditions, this requires 5 minutes.
  • If desired, the coated surfaces may be bonded up to 1 hour after application. Using firm hand pressure, adhere jacket flap and smooth entire length of seam to assure intimate contact.
• Alternate Application Method:
  • Apply a liberal brush coat at 75 - 100 sq. ft./gal. (1.8 - 2.5 m²/l) to the underside of the lap only. Then, close lap to transfer the adhesive to the mating surface and reopen for normal open time required for solvent evaporation before making the final bond. Seal the lap with firm pressure to assure complete contact.

Clean Up

• Use solvents such as chlorinated solvents (non-flammable) or xylene (flammable) for cleaning brushes and equipment.

Features

Ready-to-Use Product Features

Fast Setting,

Water Resistant

Features & Benefits

Labeling Claims

Non-Flammable

Product Highlights

• Drion® Contact Cement is ideal for bonding the laps and seams of polyester secondary vapor barriers on cryogenic insulation systems. It maintains a strong bond between layers of polyester film even at temperatures as low as -320°F.
• Drion® Contact Cement must be applied to both surfaces, allowed to dry and then bonded with moderate uniform pressure. Gives strong immediate bond strength and allows bonding up to 1 hour after application. At temperatures below 50°F, drying time will be extended.

Packaging & Availability

Regional Availability

• Asia Pacific
• North America
• Latin America
• India/MiddleEast/Africa (IMEA)

Physical Properties

Color (Properties)

White,

Off White

Physical Form

Liquid

Properties

Note

¹ - Full coverage: Applying to both surfaces will yield 75 - 100 sq. ft. bonded surface area per gallon. As a lap adhesive: 450 - 600 linear ft. of lap per gallon (assuming 2 in wide band of adhesive at lap)

² - Tested at coverage rate of 200 sq. ft./ gal. Applied to 1/4 inch (6.4 mm) inorganic reinforced cement board. The flame spread may vary at different product thicknesses and/or when applied over other surfaces.

Application Properties

	Value	Units	Test Method / Conditions
Service Temperature Limits (at coated surface)	-29 to 93	°C	-

Flame Characteristics

	Value	Units	Test Method / Conditions
Flame Spread²	10	-	ASTM E84
Smoke Developed²	0	-	ASTM E84

Typical Properties

	Value	Units	Test Method / Conditions
Average Non-Volatile Content	19	Vol(%)	ASTM D2369
Average Non-Volatile Content	21	Wt(%)	ASTM D2369
Bonding Time Range	5 - 60	minutes	-
Coverage (as a lap adhesive)	450 - 600	ft²/gal	-
Coverage (full)	75 - 100	ft²/gal	-
Coverage Range (0.011 in. to 0.008 in. wet film thickness)	150 - 200	sq. ft./gal.	-
Density	11.2	lbs/gal	ASTM D1475
Flash Point (wet flammability)	40	°C	-
Storage Temperature	4 - 38	°C	-
Volatile Organic Compound Content	7	g/L	-

Regulatory & Compliance

Certifications & Compliance

UL Certified,

Materials Analytical Services (MAS) Certified Green

Chemical Inventories

DSL (Canada),

ENCS (Japan),

IECSC (China),

PICCS (Phillipines),

TSCA (USA)

Quality Standards

NFPA 90A,

NFPA 90B

Storage & Handling

Storage Conditions

Store between 40°F and 100°F.

Shelf Life

12 months