Foster® Cryogenic Vapor Stop Sealant 90-66
1 of 48 products in this brandFoster® Cryogenic Vapor Stop Sealant 90-66 is a two-part elastomeric sealant designed for cryogenic applications as a vapor stop sealant. It is suitable for use with various insulation materials such as polyurethane foam, polyisocyanurate (PIR) foam, cellular glass, fibrous glass, aerogel, and other rigid and flexible insulations. This sealant is compatible with aluminum, stainless steel, metals, wood, and masonry construction materials.
RTU Product Type: 2K (2 component) Sealant, Elastomeric Sealant, Solventborne Sealant
Application Area: Cryogenic Applications
Application Method: Brush, Roller, Spray
Compatible Substrates & Surfaces: Aerogel, Aluminum, Cellular Glass, Fiberglass, Masonry, Metal, Polyisocyanurate, Polyurethane (PU) Foam, Stainless Steel, Wood
Features: Excellent Moisture Resistance, Low Application Temperature, Moisture Resistant, Vapor Barrier
Enhanced TDS
Identification
- GBU
- RTU Product Type
- Categories
Applications
- Application Area
- Application Method
- Compatible Substrates & Surfaces
Applications & Uses
- Coverage Range
-
- Subject to the type of surface being coated.
- 3.0 to 3.5 gal./100 sq. ft. (1.22 to 1.43 l/m2) on a smooth non-porous surface.
- Porous or rough surfaces will require higher gallonage to attain required dry thickness
- Dry Thickness: 0.031 to 0.036 in. (0.79 mm to 0.91 mm)
- Equivalent Wet Coverage: 0.048 in. to 0.056 in. (1.22 mm to 1.42 mm)
- Limitations
-
- Store and apply between 40°F and 100°F.
- Always test plastic materials for compatibility when using a solvent-based product.
- Make certain this product is completely dry and the area free from solvent odor if food is involved.
- Not suggested for application between two impermeable surfaces. As a vapor stop sealant, ensure the coating is able to fully dry after application. Do not trap solvent from 90-66 between the pipe and impermeable insulation or layers of impermeable insulation.
- Not suggested as a joint sealant in impermeable insulation where the solvent will be trapped in the joint.
- Not intended as an exposed finished coating for extended periods of time.
- Preparation and Application Information
-
Material Preparation
- Mixing Instructions: Add 90-66 Part B into Part A and mix thoroughly for about 5 minutes, using an air driven mechanical stirrer. Do not whip air into the product.
Application
- Apply only to clean, dry surfaces.
- When used as a vapor barrier and/or vapor stop, 90-66 may be applied up to 2 gal./100 sq. ft. (0.81 l/m2) on vertical surfaces (21 mils/0.53 mm dry thickness). Apply in two coats with Mast-a-Fab® reinforcing mesh embedded between coats. Reinforcing mesh must be used for cryogenic applications.
- Apply the 90-66 two to three inches on the pipe and extending up over each layer of insulation and onto the outer insulation surface. Avoid trapping solvent from wet 90-66 between two impermeable surfaces such as the pipe and insulation.
- For best results the first coat may be applied followed by immediately embedding the Mast-A-Fab reinforcement. Allow the first coat to tack up for 2 hours or longer and re-smooth the mesh before applying the additional coat(s) to complete the seal. Be sure the mesh is smoothed into the tack coat before it completely sets and before the finish coats are applied.
- When applying over rough or porous surfaces increase the coating volume to fully seal the surface leaving a minimum 31 - 35 mils (0.8 to 0.9mm) dry film thickness on the surface. Inspect for pinholes and over coat as necessary to complete a pinhole free finish. This may take 50% more material to achieve a full coating film with mesh embedded. Note: The pattern of the mesh may still be visible, but it must be completely covered.
- When selecting mesh reinforcement Foster Mast-A-Fab is strongly recommended based on its mesh size, membrane thickness and flexibility. In all cases the mesh must be an open weave mesh allowing it to be embedded into the wet 90-66 sealant and be sufficiently thin such that the dried 90-66 film covers the entire mesh. Too thick a mesh may prevent formation of a full film with the mesh embedded completely.
- Always allow the 90-66 to fully dry before covering with abutting insulation or jacketing.
Clean Up
- Use solvents such as chlorinated solvent (non-flammable) or mineral spirits (flammable) for cleaning tools and equipment. Completely clean all equipment before pot life expires and the adhesive sets up. 90-66 when dry is extremely difficult to remove.
Features
- Ready-to-Use Product Features
Features & Benefits
- Labeling Claims
- Product Highlights
-
- Cryogenic Sealant has excellent resistance to moisture, water vapor and other gasses.
- It is designed for very low temperature applications to seal seams where a water vapor tight insulation system is required.
- It is an excellent vapor stop material for use on cryogenic pipe lines and cryogenic equipment.
- Cryogenic Sealant contains no lead, asbestos, mercury, or mercury compounds.
Packaging & Availability
- Regional Availability
Physical Properties
- Color (Properties)
- Physical Form
Properties
- Note
-
Temperatures below 70°F, thicker films and applications between substrates will prolong dry time and require longer cure times.
- Application Properties
-
Value Units Test Method / Conditions Service Temperature Limits (at coated surface) -196 to 82 °C - - Typical Properties
-
Value Units Test Method / Conditions Average Non-Volatile Content (mixed) 65 Vol(%) ASTM D2369 Average Non-Volatile Content (mixed) 73.5 Wt(%) ASTM D2369 Coverage (0.031 - 0.036 inch dry thickness) 3 - 3.5 gal/100ft² - Coverage (0.048 - 0.056 inch Equivalent wet coverage) 3 - 3.5 gal/100ft² - Density (mixed) 9.6 lbs/gal ASTM D1475 Drying Time (at 73°F, 50% RH, full cure) 2 week - Drying Time (at 73°F, 50% RH, through) 48 hours - Flash Point (wet flammability) 24 °C ASTM D93 Mix Ratio (by volume) 1:1 - - Pot Life (at 77°F) 6 - 9 hours - Storage Temperature 4 - 38 °C - Water Vapor Permeance (at 100°F, 90% RH, 0.020 - 0.025 in. dry film thickness) 0.01 perms ASTM F1249
Regulatory & Compliance
- Chemical Inventories
Storage & Handling
- Shelf Life
-
12 months