H.B. Fuller

Applications & Uses

Clean Surface

The surface condition of the mating parts has an enormous influence on the success of a bond. To achieve good bonding success the mating parts should be clean.

LINOP Equipment

Cyberbond offers by means of the LINOP Equipment range suitable dosing and LED based curing devices. We also refer to suitable dosing tips which help an economical use of the adhesives (also if used manually).

Solvent Resistance

Solvent	Example	Resistance
Alcohol	Ethanol, Methanol	Very Good
Ester (aliphatic)	Ethyl Acetate (Acetic Acid Ethyl Ester)	Very Bad
Ketones	Acetone, Benzophenone	Very Bad
Aliphatic hydrocarbons (alkanes)	Petrol, Heptane, Hexane	Good
Aromatic hydrocarbons	Benzene, Toluene, Xylene	Good
Halogenated hydrocarbons	Methylene Chloride, Chloroform, Chlorobenzene	Very Bad
Weak acqueous acids	Diluted Nitric- , Muriatic-, Sulfuric- , Phosphoric Acid	Very Good
Concentrated acid	Nitric Acid, Muriatic Acid, Sulfuric Acid, Phosphoric Acid	Very Bad
Weak acqueous bases	Diluted Sodium Hydroxide -, Caustic Potash Solution	Very Good
Concentrated bases	Sodium Hydroxide -, Caustic Potash Solution	Very Bad
Water		Good
Iso-propanol		Very Good
Acetone		Very Bad
Mineral oil		Good

Features

Ready-to-Use Product Features: Alcohol Resistant,

Fast Setting,

Low Viscosity,

Water Resistant,

Fast Bonding

Features & Benefits

Product Highlights

Cyanoacrylates are fast setting, one component and solvent free adhesives. They are based on esters of cyanoacetic acid. To get to a finished product, mainly thickeners, respectively film forming agents (polymer methacrylics and acrylics) and stabilizers are added. The polymerization is initiated by present humidity. Best results are given between 40 to 70 % relative humidity.

Cyberbond standard grades are as follows:

Powerdrop series (stabilized ethyl ester)
Elastomer and plastic series (ethyl ester)
Neomer Series (surface insensitive ethyl ester)
xtraflex series (rubber toughened ethyl ester)
metal series (ethyl ester)
low odor series (alkoxy ester)
medical series (butyl- and octyl ester)

Identification & Functionality

Base Compound: Ethyl - 2 - cyanoacrylate

Packaging & Availability

Regional Availability

Asia Pacific
Europe
North America
Latin America
India/MiddleEast/Africa (IMEA)

Physical Properties

Physical Form: Liquid

Properties

Density:

1090 kg/m³

Flash Point:

80 °C

Shelf Life:

12 months

Specific Gravity:

1.09

Viscosity:

40~100 cps

Physical Properties


	Value	Units	Test Method / Conditions
Density	1.09	g/cm³	-
Flash Point	82.5	°C	-
Service Temperature Range	-55 to 95	°C	-
Set Time (Acrylonitrile Butadiene Styrene)	4 - 6	seconds	-
Set Time (metal - steel)	20 - 60	seconds	-

Cured Properties


	Value	Units	Test Method / Conditions
Strength of Cured Adhesive (Nitrile Butadiene Rubber, cured)	5 - 12	N/mm²	-
Strength of Cured Adhesive (steel, cured)	14 - 28	N/mm²	-

Typical Properties


	Value	Units	Test Method / Conditions
Viscosity (at 20°C, 160rpm)	40 - 100	cPs	Cone-Plate Viscometer

Processing Parameters


	Value	Units	Test Method / Conditions
Setting Time (EPDM)	6 - 12	sec	-

Regulatory & Compliance

Specification

NSF Nonfood Compounds Registration Program,
This product is acceptable for use as an instant adhesive in food processing facilities.
This product must only be used in a manner as to ensure it will have neither direct nor indirect contact with food or potable water.
Category Code: P1, Registration Number: 150471
RoHS conform.

Safety & Health

Potential Danger of Cyanoacrylates

You should care for the following:

Use in well ventilated areas only
Installll suitable exhaust systems in the workshop
Apply material economically and use a dosing system where appropriate
Allow a consistent relative humidity of 50 to 65 %; with regards to lower figures the polymerization will be delayed and monomer adhesive fume will appear
If necessary: wear suitable, non-sucking gloves (Eg. No cotton)
Keep adhesive out of reach of children

The data mentioned in this TDS, particularly the recommendations and use of products are based on our recent knowledge and experience. Due to the fact of having so many different materials involved and conditions of applications which are out of our influence, we strongly recommend to do sufficient tests in order to guarantee that Cyberbond products are suitable for the intended process and applications. Except for wilful acts any liability based on such recommendations or any verbal advice is hereby expressly excluded.

Storage & Handling

Storage Conditions: Cyberbond® 1070 should be used within the shelf life specified on the packaging. The storage stability applies to material stored under appropriate conditions only (original unopened containers, recommended storage temperature). This product should be stored unopened in a cool, dry place out of direct sunlight. Refer to the Technical Data section of this document for optimum storage temperatures.
Shelf Life: 12 months (at 20°C, unopened)

Technical Details & Test Data

Measurement of Viscosities

Viscosity describes the flow-ability of a liquid. Cyberbond measures the viscosity of the products by means of the cone/plate method: the liquid is applied on a panel and a defined cone presses the liquid together and rotates. You differentiate between a Newtonian and a thixotropic liquid. In terms of a Newtonian liquid you will get a relative constant viscosity graph in dependence of the rotary speed of the cone. In terms of thixotropic liquids the product becomes more liquid (down to its base viscosity) the faster the cone rotates. The viscosity is measured in mPa*s (milli Pascal x second) [SI system] or in cP (centipoise) [CGS- system]; 1 mPa*s = 1 cP. In order to allow products comparison all adhesives are measured at the same rotation speeds.

Newtonian liquids at 160 upm
Thixotropic liquids at 0,5 upm and at 160 upm

Temperature always is at 20 °C / 68 °F, if not mentioned to be different.

Technical Details

Hot Strength on Steel

% of RT strength, tested at temperature.

Cyberbond CB 1070 - Technical Details

Time Until Full Cure

% of RT strength

Cyberbond CB 1070 - Technical Details - 1

Strength of cured adhesive

Substrate	N/mm2
NBR-rubber ▲	5 to 12
steel	14 to 28

▲ material failure

Cyberbond CB 1070 - Technical Details - 2

Heat Aging - on Steel

Tested at 20°C

Cyberbond CB 1070 - Technical Details - 3

Durability after Storage under Changing Climatic Conditions

Test with stainless steel
Above freeze point 80%rel. humidity
Temperature range: -20 - 80 °C
Cycle count - 60

Holding time at start temperature - 0
Heating up phase - 3
Keeping warm phase - 3
Cooling down phase - 3
Holding time at final temperature - 3

Cyberbond CB 1070 - Technical Details - 4

Cyberbond CB 1070

Enhanced TDS

Identification

Application Information

Applications