H.B. Fuller

Enhanced TDS

Identification

Chemical Family: Polyurethanes (PU)
GBU: HHC
RTU Product Type: 2K (2 component) Adhesive,

Reactive Adhesive,

Structural Adhesive

Categories: Markets → Consumer Goods → Applications → Appliances & Electronics

Markets → Consumer Goods → Applications → Footwear

Markets → Consumer Goods → Applications → Sports & Recreation

Technologies → Adhesives & Sealants → Product Families → Bonding Technology → 2K Liquid Reactive Adhesives

Technologies → Adhesives & Sealants → Product Families → Functional Adhesives → Structural Adhesives

Applications

Application Area: Industrial Conveyors,

Rollers,

Refrigerators
Compatible Substrates & Surfaces: Ceramic,

Plastics,

Elastomers & Rubbers,

Fibers & Fabrics

Applications & Uses

General Instructions: To obtain the best cured properties, accurate proportioning and thorough mixing are essential. The production of the desired polyurethane requires accurate measurement of the two components and adequate mixing. In general, hand-mixing small production runs is easily accomplished by weighing the two components. Machine mixing utilizes the volumetric ratio. Most machines are calibrated by weighing the components and adjusting the volume ratio. Larger volume hand mixing is easily controlled by filling pre-measured buckets to the indicated heights. Surface must be clean and dry before application. Remove all chemicals, dirt, wax and oil. Abrading or of the bonded surface is recommended. Pre-cleaning with a mild solvent such as acetone or acetone-containing blends will enhance bonding characteristics over high-flexibility substrates.

Features

Ready-to-Use Product Features: Good Non-Yellowing Properties,

Good UV Resistance,

High Flexibility,

High Impact Performance,

High Resilience,

Medium Hardness,

Rapid Cure Response,

Water Resistant,

Good Peeling Strength,

Room Temperature Curing

Features & Benefits

Features and Benefits

Excellent impact performance
High peel strength
Clear with high resistance to UV light (yellowing and breakdown)
Bonds a wide variety of substrates including metals, ceramics, natural rubber, thermosetting polymers and many engineering thermoplastics

Packaging & Availability

Regional Availability

Europe
India/MiddleEast/Africa (IMEA)

Physical Properties

Color (Properties): Transparent
Physical Form: Liquid

Properties

Application Temperature:

66 °C

Density:

1000 kg/m³

Specific Gravity:

Viscosity:

12000 cps

Note

The cure schedule is dependent upon the temperature. The recommended cure schedule will vary with the desired properties. Various heat-cure profiles may produce suitable results.

Uncured Properties


	Value	Units	Test Method / Conditions
Full Cure (at 25°C, full)	24	hours	-
Gel Time (at 25°C, 200g)	15	minutes	-
Handling Time	90	minutes	-
Mix Ratio (by volume)	100:100	-	-
Mix Ratio (by weight)	100:100	-	-
Operating Temperature	66	°C	-
Specific Gravity	1	-	-

Cured Mechanical Properties


	Value	Units	Test Method / Conditions
Hardness	50	Shore D	ASTM D2240
Overlap Shear Strength (at 50% RH, aluminum, acid etched 24h)	400	psi	ASTM D1002
Water Absorption (at 25°C, 24h, weight gain, immersion)	1.1	%	-
Water Absorption (at 25°C, 30 days, weight gain, immersion)	1.2	%	-
Water Absorption (at 60°C, 24h, weight gain, immersion)	1.2	%	-
Water Absorption (at 60°C, 30 days, weight gain, immersion)	1.4	%	-

Component A


	Value	Units	Test Method / Conditions
Viscosity (at 25°C)	12000	cPs	-

Cured Properties


	Value	Units	Test Method / Conditions
Elongation at Break (at 50% RH)	403	%	ASTM D638
Open Time	15	minutes	-
Tensile Strength (at 50% RH)	905	psi	ASTM D638

Typical Properties


	Value	Units	Test Method / Conditions
Storage Temperature	16 - 27	°C	-

Component B


	Value	Units	Test Method / Conditions
Viscosity (at 25°C)	2000	cPs	-

Rheological Properties


	Value	Units	Test Method / Conditions
Viscosity (at 25°C, mixed)	4000	cPs	-

Storage & Handling

Storage Conditions: These materials should be stored in a dry environment within a temperature range of 16 °C to 27 °C (60 °F to 80 °F). Extremes of temperature beyond this range may result in crystallization or polymerization of the materials. Introduction of a nitrogen blanket into the containers before closing will improve the storage life of the products. When using meter-mixed dispense equipment (MMD) machines, reservoir should be blanketed with nitrogen or dry air to avoid moisture and other contamination. Avoid contamination with oxidized metals (such as copper, brass, or mild steel), and rust or other metal oxides. The stability of the product is greatly reduced by materials such as strong acids or bases, sulfur compounds, amines, or reducing agents of any type.
Shelf Life: 18 months (double/bubble packaging), 6 months (unopened)

H.B. Fuller 42223/52223